Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Whirlpool gold quiet partner 3 model # GU2455XTSSO will fill with water and heat up. It will not wash. There is a buzzing sound from the dishwasher. I pushed the heated dry, high temperature button d3 came up. It will pump out when I push cancel. What can I do?


Answers :

Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool gold quiet partner 3 model # GU2455XTSSO will fill with water and heat up. It will not wash. There is a buzzing sound from the dishwasher. I pushed the heated dry, high temperature button d3 came up. It will pump out when I push cancel. What can I do?


... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool gold quiet partner 3 n the cancel button won't go off n the normal wash button won't go off either. I can do a quick wash cycle on it but then goes right to sani rinse afterward n don't shut off itself it just keeps on going. Solution? Is there a reset for it because I have an air dry button but not a heated dry button so I don't kno if I should push sani rinse/air dry two times over as opposed to sani rinse/ heated dry or if there's a diffrent solution for it. This all starte


... Dishwashers

KitchenAid dishwasher, Model # KUDP021RBS1 - "Normal and cancel lights blink constantly". I had this same problem about two weeks ago so I googled your site and though the solution I found was not exactly applicable to my problem but I tried and that is - Press high Temp, heated dry, high temp and then heated dry and then cancel button and then close the door. Would you believe it worked like a magic wand. But this same problem resurfaced and I am trying all those old tricks but nothing is worki


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

The stop/cancel light keeps flashing. I have tried Heated dry to Normal sequence buttons and I have tried Heated dry to High temp wash sequence. When I have pushed soak and scour the stop/cancel light stops and the Pot/pan and Normal wash lights start blinking


Unfortunately I cannot view the comments from other fixya.com consultants so I am coming in cold on this one.\015\012\015\012But it appears you are trying to isolate the problem of why the stop/ cancel light are flashing. I suppose the on ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

My Kenmore dishwasher has the lock-on light that is stuck in the ON (lit) position freezing any other action. I have tried cancelling it, shutting off the power and resetting it with the "Heated Dry - Normal-Heated Dry-Normal" pushing of the buttons with no success. Ideas?


I held the "Heated Dry" button down until the lock light went out. It may have been 10-15 seconds. All seems well now. ... Dishwashers

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

Light flahing My dishwasher normal wash light just keeps flashing. When I press the cancel button it also starts to flash. I have tried going between the high temp and sani wash and the high tem and heated dry but noithing happens. Do you have any solution for me. Thanks LYNN


The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with the temperature sensing circuits in some dishwashers that causes an error code to be generated if a certain water temper ... Kenmore 13732 / 13734 / 13739 Dishwasher

The lights on the dishwasher are off now after pushing heat dry heat temp the problem is that their is water in the bottom of the dish wassher and it will not drain using the cancel button..


Sorry to read about your problem, I hope this helps you out.You may have a defective pump, on a control card issue...you may also try to reset the circuit breaker, and see if that helps. If not i suggest you contact a service compan ... Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

My dishwasher Frigidaire FDB1500LFC2 will stop in the first cycle and the "High Temp" and "Heat Dry" lights flash together. If I push cancel it will drain. It just will not complete a wash cycle.


... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I opened the door before the drying cycle finished. I pressed the cancel button, then I pressed "normal wash" and the "start" button and it didn;t start. Then did "cancel" again . I pressed the "heat" button for five seconds to lock the door so I wouldn;t make the same mistake again. It still won't start. Now the "cancel" button won't work and the start button flashes. What do I do now?


HI. The unit will need to be reset. This is achieved by unplugging the unit for five minutes. If unplugging is not an option, simply,shut down the appropriate circuit breaker for five minutes. This action will, essentially, reset the logic sector. On ... Dishwashers

Dishwasher whirlpool GU2475XTVY - I've tried the high temp/heated dry/high temp/heated dry sequence- most lights come on ... i've tried it with /without open door / pressing cancel, etc. after pressing sequence only FIVE lights come on (rinse, high temp, sani, heated dry, cancel. after the


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Whirlpool Quiet Partner II dishwasher will not start. Thye Heated Dry Light is flashing and presssing the Cancel button does not resolve the matter. Also pressing the Heated Dry button for 4 seconds does not resolve the matter either. Please help. Thanks Jim Sparks


Have you tried powering it down,shutting off power to the unit for 15 minutes,sometimes the electronics will glitch as a computer does,if this is to no avail,then try removing all connections from the interface(control panel) to the main control pane ... Whirlpool Dishwashers

The glass xpress light on my Whirlpool GU 2400, Quiet Partner III, is flashing. I tried alternating the sani rinse and heated dry buttons, and alternating hi-temp wash and heated dry---nothing changed. None of the option buttons light up when they are pushed. and the time remaining stays on -- (two dashes), the dashes don't move. Any other ideas?? PLEASE


... Whirlpool GU2400XTP Built-in Dishwasher

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Maytag MDBH985AWS...control panel button to turn on the washer does not work...wash cycle and delay lights will light when pushed but washer will not come on. Have tried pushing normal wash and heated dry in sequence, flipped circuit breaker, open and close door, pushed buttons while door is closed


... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1190 seconds