Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

It has a hard time getting enough water to pump up to the top. I have to start it a couple of time before it gets enough water going


Answers :

I had the same problem. With other tips from this site I was able to find the solution. The cause? A cherry pit. Yes, a cherry pit broke the chopper assembly, a small food processor looking blade that chops the food before it hits the filter. With the broken blade the filter clogged quickly and didn't allow sufficient water pressure to clean the upper rack as well as the lower rack. You may have a broken chopper assembly or the filter is just clogged. Good Luck!
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It has a hard time getting enough water to pump up to the top. I have to start it a couple of time before it gets enough water going


I had the same problem. With other tips from this site I was able to find the solution. The cause? A cherry pit. Yes, a cherry pit broke the chopper assembly, a small food processor looking blade that chops the food before it hits the filter. With th ... Whirlpool GU2400XTP Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Often had to press 'Start' up to 5 times to get it going. All lights light up but then go out. Occasionally the pump would run for a minute or so then whole shooting match would close down. Recently we were lucky and it filled with water but sadly disappointed when it closed down again. 8 people in the house so had to do the dishes in the sink (again!!). Plenty of helpers and a glass or two of wine so things weren't that bad. Not good for Dishlex though especially when others say theirs are


Problem not solved yet.\015\012Cleaned the filters well, hoses clear and water delivery happens.\015\012Both pumps work happily so are not seized/locked up or have anything jambed in them (pulled them both out and checked for foreign obje ... Dishwashers

I have a Bosch dishwasher she44c05uc/40 It is 3-4 years old. Recently I noticed that the cycle times have gotten much longer. Since then there is a sewer smell in the washer especially when starting a new cycle it comes out of the disposal. I'm wondering if the pump isn't heating the water hot enough. I've also noticed that the dishes aren't getting near as clean as they were before all this started. Especially stuck on food. It used to clean everything now dishes almost need rinsed.


Hello,Welcome to FixYa ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

Hi I am in an emergency situation with an ikea whirlpool dishwasher. I have no idea what model it is since it's built in and I can't find the manual in my rental apartment. The machine works normally until the part where it's supposed to pump the water out after rinsing. At this point it starts to beep, once, and then 3 times. On and on and on. If I open it, there is water stagnated there. If I try to turn it off and back in, it will go through a whole new program and then I get the same problem


Can you feel the pump operate during the last wash cycles? if not either theres a bad pump motor or lack of power to the pump during that cycle,if this is ok,then remove the drain hose to the main drain to see if this is plugged up with food debris ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

We have a Bosch dishwasher. The manual says for models SHV46C13, SHX43C0 so I guess it is one of those. It stopped working and when I opened it there was a bunch of cloudy soapy water on the bottom. The power was not coming on at that point. I have noticed that lately when I go to push the on button, the light will go on and when I shut it it doesn't start. After a couple times of turning it off and on it will run normally. This has only happened a couple times though....


... Bosch Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

After starting the cycle, the dishwasher starts and runs normally for a short time, then the water drains out of the tub prematurely while the cycle is still going. The machine then runs dry until the cycle times out. At the next cycle and the process repeats. It started as a sporadic problem, but is getting worse.


You may have a faulty drain valve,the drain valve is under dishwasher there are two clips on each side check,with applance store for replacement part. ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

The dishwasher pump will not shut off. Keeps going even after the dishwasher has been emptied of all water. Then the beeping sounds starts and will not shut off.I took it out thinking that I could get to the pump to see if there was something stuck in it but can only get limited access to it


Depending on the model, your float is off the switch\015\012 it is a round piece in either corner, that should float up and down\015\012 if you remove your toe kick and look at the bottom of that, you will see where the float comes throu ... Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Just got a used F&P Smart Drive 5.5 MW059. First few times I used it wouldn't always start on certain settings but once it did start it ran through just fine. On the fourth use, it was very difficult to get it to start and it just stopped after it filled up. Pausing and restarting, shutting of machine and retrying did not help. Was able to advance to rinse mode and got machine to drain water; however, instead of going into spin mode it just attempted to drain continously. I let it do its th


Did not realise this is a washing machine and not a dishwasher.\015\012\015\012Looks like some consultant has already been dealing with you on this problem.\015\012\015\012Hard to say if it is a simple as an inlet solenoid val ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2008 seconds