Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


Answers :

If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor.
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Rebadged Siemens dishwasher model no. SE6TIE1GB / 13 TKD 795 / 2. When turning on, the dishwasher makes the "normal" noise of washing but after less than a minute it stops and refuses to wash anything. Ive tried pressing the reset button but no help. Worth mentioning, the night prior to that, I switched on the dishwasher before sleeping and when waking up at 5am, it was still washing so I manually turned it off and opened the door to find some water at the bottom of the tray.


... Siemens Dishwashers

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Model #363.14232100 dishwasher. When you turn the switch to on, it will not come on. If you keep turning the knob slowly you can hear the dishwasher trying to start up,but it doesn't. Keep turning the knob and its the same thing, sounds like it will start, but it doesn't. It did fill with water, but once it was opened it didn't start up where it left off. The lock switch was in position, and still nothing. Now I have water in the bottom but can't get the thing to come on. Any suggestions? Help!


... Kenmore 24 in. 16539 Built-in Dishwasher

Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?


There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

The top dishwasher is flashing F1 and the motor won't turn off. It will drain if I pour a cup of water in it. The bottom dishwasher is working just fine. There is no water in the bottom pan. I usually find a few drops of water when it's flashing F1. Thank you!


Hi.the troubleshooting, and the error code depends on the make of the dishwasher.If the dishwasher does not stop draining, then the float sensor switch, or the pressure switch in the drain system is faulty.Details ... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

Recently there's been a white coating on dishes. Has to be scrubbed off manually or soaked in a vinegar/water solution. I flushed out the rotating arms to be sure water flows thru & it does. Checked bottom filter & basket...both clean. Twice used "finish" cleaner for dishwashers in the scrub cycle as directed. Turned off during drying cycle and now there is water across the bottom of the dishwasher. Next? Thanks for any help. Rosemary


Use any brand of dishwasher cleaner from a local store and run your dishwasher with it.I would also recommend that a calcium lime and scale remover be ran through your dishwasher to clean it out.\012this may have to be done a couple of times. ... Kenmore Dishwashers

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

My wife opened the Dishwasher in the middle of a cycle and turned the cycle to off. Dishwasher will not turn on. Power is ok. Bottom of Dishwasher is full of water. How can we get the dishwasher to restart?


... General Electric Spacemaker® GSM1800N Built-in Dishwasher

Hi, When I turn on my dishwasher, it fills as normal with water but is not pumping into the upper spray arm. the spray arms are not clogged, I have checked them. Anyway, I always rinse the dishes under the tap before placing them in the dishwasher. I have to switch the machine on/off several times then the pump starts at full force.Occasionally it goes through a complete cycle without havig to switch on/off. It's a Siemens Lady model, E-NR SN53300GB/08, FD 7201 058479. The dishwasher is used


... Dishwashers

I have a Hoover dishwashe HND 6515. I put it on the universal 65c programme this afternoon and sfter 5 mins it started a continual beep beep beep noise and the red light on the universal button was flashing, I then notices it was emtying water all over the kitchen floor, seeming to come from under the bottom of the door. I turned it off and when it finished pouring out water opened it up and the bottom of it is full of water which will not drain away. I have checked the filters and they are all


... Hoover Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

We have a Diplomat dishwasher ADP 8242 and its intergrated but have no manual, the machine switches on fine and starts its cycle, i switched it on before going to bed and in the morning it was still running so obviously knew something was wrong, when i opened it the dishes were not clean and there was water in the bottom which took a while to drain away, also the salt inlet is full of water, should it be like that? Any advice would be great thank you.


... Dishwashers

Lately the soap remains in the dispenser, dried and caked in (I have to dig it out with a sharp object, as it becomes a solid piece). I have also tried gel soaps, but find them in the bottom of the dishwasher, partially intact. The mistery is this does not happen all the time, but most of the time! I've checked the water pressure and the water temperature: both seem to be fine. The dishwasher does run a full cycle. Is it time to buy a new one? Would you also be able to tell me what year this mod


... Frigidaire 24 in. GLD3450RD Built-in Dishwasher

I noticed water coming from underneath my dishwasher so I pulled it out from the wall and found that underneath the factory installed installation there was a screw missing that holds the top dishwasher rack. The hardwood floor and bottom of the cabinet is ruined. While finding this problem, I also found rust on the bottom of the rack. Who do I need to speak with about this problem?


Speak with who you purchased the dishwasher from. They will be able to point you in the direction to get a replacement and file a complaint. All of this is provided you bought the machine in the last year. ... Kenmore Dishwashers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

We are having a small leak near the front valve or hose connection in our Kenmore dishwashers. This tends to happen when we are out of town and have turned the household water off. The dishwashers also has water in the bottom when we return. We have tried to set up the situation to make it leak in order to find it, but have not been successful. Have there been similar complants?


... Kenmore 16762 Dishwasher

We haven't used the dishwasher for a while. Now we get no water to the tub. I know we have to take the bottom off and turn something, but what is "that" called and where can I find it. I still have the book for the dishwasher so I can find what needs to be repaired, if I knew what is was.


... Dishwashers

My Maytag Quiet Series 200 Dishwasher Model MDB6600AWW washes the dishes but does not go into it's rinse cycle and does not stop. I have to turn switch off at the wall to get dishwasher to stop. The water is hot and the dishes appear clean but it doesn't turn off.


... Dishwashers

I purchased a diswasher (Hotpoint)about 1-1.5 years ago. It's model # is HDA3400G02CC and its SS# is TH887451Y. I don't think I registered it. No Matter, Two days ago, my garbage disposal stopped working. I checked the outlet. It had power. The switch to the Disposal was next to the outlet. I assumed that the switch was wired from the outlet. It wasn't. Bottom line, the switch nut was loose. I tightened it and problem solved. When I turned on the dishwasher, nothing happened. It acts like


I purchased your service (telephone support) and the dishwasher expert contacted me. We discussed the issue, he made recommendations. I followed his advise and solved the problem. Before I could recontact him, he called to follow up on my progress. ... GE Dishwashers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2820 seconds