Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

(cycle lights) flashing "pots&pans", steady "normal", 2 steady dash marks on "time remaining" m/n GU2400XTPS3, s/n FS1212944


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press these buttons in\015\012sequence...
\015\012\015\012
\015\012-high temp wash

\015\012\015\012-heated\015\012dry
\015\012\015\012-high\015\012temp wash
\015\012\015\012-heated\015\012dry
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do accept the solution if the issue is\015\012resolved or post a comment for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

(cycle lights) flashing "pots&pans", steady "normal", 2 steady dash marks on "time remaining" m/n GU2400XTPS3, s/n FS1212944


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press t ... Whirlpool GU2400XTP Built-in Dishwasher

I have never had any problems bought 3 yrs ago,now last night dishwasher stops and we have a clean light on,but not steady light,flashes 7 times...anyway i can reset this machine? jim


... Kenmore 24 in. 16034 Built-in Dishwasher

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light continues to flash and if I push the cancel/drain button then it starts a steady flash


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Hello my Kenmore built-in dishwasher (model: 17352) has a flashing light as of yesterday. The "clean" light flashes 7 times then pauses then flashes 7 times continuously. I don't have the troubleshooting manual. What does this indicate?john Racette


... Kenmore 24 in. 17352 / 17354 / 17359 Built-in Dishwasher

Whirlpool dishwasher gu3600 The pots & pan, normal light and delay lights flash all the time. Also the time remaining screen has two horizontal lights on. The dishwasher won't start


... Whirlpool Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Re: Whirlpool Dishwasher When I press the ON button it goes green for a few seconds and I hear the dishwasher starting but doesn't fill. Then the green light ON Light flashes 6 times, stops, and flashes again 6 times and so on until I turn it off. Dishwasher will not fill. Please help


... Whirlpool Dishwashers

Light flashing light clean flash seven times what i should do please help gu2500xtb1 blinks 7 times how do i diagnose and fix


Reset the dishwasher by touching heated dry and normal let it run through that cycle then through a normal cycle got the error blink again. Reset dishwasher by touching heated dry and normal, ran the test cycle, next ran a normal cycle but turne ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

Viking dishwasher ddb200ss will not reset...the pots & pans light flashes 3 times and then the normal wash light flashes 1 time...How do I reset this type of dishwasher


... Viking Dishwashers

It stops when it has only done the rinse cycle and a light flashes 4 times quickly and pauses and the light flashes 4 times again and again


The IC module controlling the rinse operation is faulty. It is not sending the control to the next module. Or the IC module controlling the drain operation, which is not taking the signal to get working. Either of the two is at fault. Please have it ... Dishwashers

I have a kenmore dishwasher mo. no.665.17039401 the clean green light flashes 7 times and it keeps doing that if i try to start the dishwasher on the start button a red light flashs three times what do how do i fix it .i made shure the door was locked


... Dishwashers

She6af02uc bosch dishwasher Light is flashing but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Dishwashers

She6af02uc bosch dishwasher Light is flashing, but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing, but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Bosch Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

My dishwasher will not start just these three lights are flashing at the same time. What should I do? The three lights that are flashing are smart wash , normal wash and cancel drain. The dish washer


Try turning breaker panel for that off, and back on. might just need to be reset. If that doesn't work, call the repair man ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0922 seconds