Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

I recently installed a new garbage disposal and since then my dishwasher won't drain. Is there something i'm suppose to reset or something?


Answers :

Sorry to read about your problem, I hope this helps you out.

remove you garbage disposal, look at the hole where you hooked the dishwasher. get a large screw driver and hammer and place in hole, and knock out the plug. if you put your finger in the hole, you will see it does not go thru... REMOVE THE PLUG AS IT FALLS INTO UNIT.

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question's. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I recently installed a new garbage disposal and since then my dishwasher won't drain. Is there something i'm suppose to reset or something?


Sorry to read about your problem, I hope this helps you out.remove you garbage disposal, look at the hole where you hooked the dishwasher. get a large screw driver and hammer and place in hole, and knock out the plug. if you put your fing ... Whirlpool GU2400XTP Built-in Dishwasher

Moved Kenmore dishwasher to new house. Installed it. It will not start. Is there a reset switch? Model 587-1541590. Electrical installation checked OK. Water connection checked OK. Is there something I should do before I call for repair person to come


You say "electrical installation checked OK"...is the machine hard wired into a junction box or does it plug into an outlet?\015\012\015\012If in a wall socket the new house circut may be on a wall switch which is currently off. If it is ... Kenmore Dishwashers

I am trying to replace the GUIDE RAIL BRACKET ASM on my GE dishwasher (model no. GSM1800JWW). How do I either: (a) remove the old brackets, and then install the new ones; or (b) remove the rollers from my new brackets, so that I could slip these rollers onto the old brackets still in the dishwasher, saving the trouble of removing the old brackets in the first place? Either solution would be acceptable, but right now I can't figure out how to do either one without breaking something. Thank you v


Be ready for both . because if they break you can still replace it. but (a) is to me the better choice. let me know how you made out and send me a 4 thumbs post if it works out ... Dishwashers

My Ge profile Triton Dishwasher wont start when I lock it just keeps beeping and the" normal "light flashes there was something stuck in the turnstile and it stopped and beeped all night when I took it out it was left this way I have turned the power off and on and I still cant reset it any ideas it just wont reset


... GE Dishwashers

We have a brand new KUDE60FVSS dishwasher that is being installed and it is POURING water out one side of the door. The handyperson checked all the connections and we cannot figure out if it's the work or the new dishwasher. Is there some secret drainstop or something that needs to be closed?


... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

I just installed a new dishwasher . The water is going to the dishwasher but it wont go into the dishwasher


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Bent leg We had tile installed and so we have to be able to adjust the legs by approx 1/2 in. to pull the dishwasher out. The timer went out and so we were going to replace the dishwasher, but the new one won't fit in our cabinet. So, while trying to put the Bosch back in, I guess the back leg hung up on something and bent ... can't screw it in, can't screw it out, dishwasher is out of level as it is. Questions as follows: 1) how important is it to have it level? 2) any suggestions on wh


It's hard to say what to do about the leg without seeing it. You should at least try to get something under it to get it level as possible. If not perfect, it is better to have it tilted slightly back than foreward. ... Bosch 24 in. SMU40 Built-in Dishwasher

Brand new dishwasher, installed last week. When it is done there is quite a lot of water standing in the bottom of the tub. It has only been run 2 times since installed and both times several inches of water were left standing. Is this something we could check or do I need to have the installer come back, which will probably take a week at least. Oh-KitchenAid #KUDC031VWH


First was a new garbage disposal also installed? There is a knockout on the garbage disposal where the drain hose connects to.\015\012If that is not the problem make sure it has the correct high loop or also called air gap. If that is not right ... KitchenAid KUDC03IVWH Builtin Dishwasher

Just installed a new Hot Point dishwasher.Mo #HDA2100N10WW. I AM HAVING PROBLEMS GETTING THE WATER TO DRAIN OUT. THE OLD MACHINE WOULD DRAIN FINE. IS IT POSSIBLE I FORGOT TO REMOVE SOMETHING ON NEW DISHWASHER?


Remove the drain hose from the sink and see if it will drain into a pail, if not then you have a problem with the machine that is covered under warranty ... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

During installation of new dishwasher when I was attaching drain hose to pump I saw a small red rubber fap attached to end of pump discharge nozzle. Is this a backflow prevention or something to keep


It is a back flow preventer. Leave it alone and attach the drain hose. ... GE Profile PDW8400J Built-in Dishwasher

There isabout 2 inches of water left in the bottom of the dishwasher after i run a cycle , and some food bits left in the water how do i drain the waterand remove the food bits? A manual was never left when the new machine was installed. We have a Quiet something 3 machine.


The filter is probably blocked.\015\012\015\012It is inside the base of the machine.\015\012\015\012Take out the filter and clean it and also clean out the filter well as that can also hold quite a bit of debris.\015\012\015\012 ... GE Dishwashers

Bosch sgv53e13gb Integrated dishwasher - wont start a new cycle!?


Thanks for the input Dicky...I think my dad will be onto the place of purchase first thing tomorrow!! ... Bosch 24 in. SGV53E03 Built-In Dishwasher

Our new home has a GE dishwasher. If I look at the steam vent on the front of the machine, I can see a piece of styrfoam. Is that supposed to be there or did they forget to remove it when they installed it?


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Have a new GE Profile dishwasher. The LED time display started at 62 the first time we used the machine. It keeps going up and is now at 108. Is it broken and how do we reset the time back to something more reasonable. We typically pre-wash the dishes anyway and it shouldn't have to take that long to clean....thanks!


Have you tried to turn the mains power to dishwasher off and back on again.\015\012\015\012It also possible the inlet water temperature is not at the recommended temperature so it is compensating for heating it to the desired temperature. ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?


... Dishwashers

GE dishwasher model ghda485n10cs brand new display and main board clean light blinking, can't reset unit wont operate.


... GE Dishwashers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

I have just installed a new melie g1243scu dishwasher when i turned it on it came up with a F70 fault (water proof system) how can i reset it


... Dishwashers

Hi. I have a Danby DDW396W countertop dishwasher brand new yesterday. We unpacked it, installed it onto taps, loaded it with dishes, and turned it on. That's where everything went wrong. When you turn it on, the display shows P2 and when you press the program button to change it, nothing happens. When you push the start button, nothing happens. What am I doing wrong? I know I'm missing something simple, but what? Please help. Katherine


Hello there and thank you for choosing fixyaThe p-2 code is a wash cycle that is the normal cycle for this unit please see below.Press the program button until the desiredprogram code appears in the display window.The ... Danby Dishwashers

Have an Aeg oko 4020 dishwasher. Installed a new pump and it worked for awhile. It now won't switch off but the cycles do not run. Someone suggested there maybe water in some area that has caused some sort of safety mechanism that has kicked in - do i need to drain something? Thanks Tom


It probably has water in the bottom tray\015\012take bottom front panel off and this exposes the bottom tray\015\012mop out water and machine will run\015\012if fault reoccure then you have a leak ... AEG Dishwashers

Dishwasher I am getting a run around with getting my LG dishwasher fixed properly. We had a tech more than once come in and look at our dishwasher. It has not been fixed and never dried the dishes properly. It is now leaking and going to a "del" level when we attempt to wash the dishes. It is also leaking on our fairly new tiled floor and under our new kitchen cabinet. Your tech stated the dishwasher was not installed properly. The installation dept , Francine stated it is not their problem


Not sure what you mean by a "del" level, but as far a drying issues:\015\012\015\012LG chose to use a very energy efficient drying method which relies on the residual heat of the dishes to help dry them rather than many manufacturer ... LG LDF6810 Built-in Dishwasher

My new Dishwasher Won't Drain, ehat to do? I have a GE model GSD2300N00WW dishwasher. A few days ago we noticed that it isn't draining. This dishwasher came installed in our new doublewide mobile home. There is no disposal, the drain hose isn't clogged, there is no air-gap installed, and the sink drains just fine. I have removed the filter and cleaned it (wasn't really dirty). Does anyone have any ideas?


... Dishwashers

IDL750 - Fuse trips when turned on. HELP! We had some electricians here to install a new electrical socket for a new fridge. They put the new socket in the same wiring as for my existing dishwasher!! The first time I tried to start the dishwasher cycle with the new fridge plugged in, the circuit box fuse tripped. Now, even with the fridge turned off, the dishwasher makes the fuse trip when turned on. Is there a fuse inside the dishwasher that has blown and needs to be replaced? or a ground brea


Hi.The first step is understanding if the problem is the socket or the appliance. Find an extension long enough to reach a different socket. Move the appliance to reach the power cord, and connect the dishwasher to a different power sock ... Indesit 24 in. IDL700 Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2465 seconds