Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

DWF 415 Ikea Whirlpool Dishwasher has constant green blinking light. Drain pump works ok (as it will pump out a jug of water if I tip it into it!) but no water comes in. Cycle stops about 30 seconds after thre is no more water to pump. Any ideas on how to fix?


Answers :

Anyone got an answer to this, as I have exactly the same fault. \012\012\012

Dishwasher appears to switch on OK, then after a short time (20 secs?) the pump noise stops and the green light flashes - it seems to e a sequence of 7 flashes, then stop... 7 flashed then stop.

The sequence could indicate a fault detected?

Anyone know anything about these units from IKEA, made by Whirlpool?

Thanks!

S
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DWF 415 Ikea Whirlpool Dishwasher has constant green blinking light. Drain pump works ok (as it will pump out a jug of water if I tip it into it!) but no water comes in. Cycle stops about 30 seconds after thre is no more water to pump. Any ideas on how to fix?


Anyone got an answer to this, as I have exactly the same fault. \012\012\012Dishwasher appears to switch on OK, then after a short time (20 secs?) the pump noise stops and the green light flashes - it seems to e a sequence of 7 flashes, t ... Whirlpool GU2400XTP Built-in Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

My dishwasher has stopped pumping water in the tub. You can turn it on to start the cycle and it comes on but it has stopped pumping water to wash the dishes. It will go all the way through the cycle and never wash a dish


... GE 24 in. GSD2220Z Built-in Dishwasher

I have a 7 yr old Miele G 641 SC Plus dishwasher, the inlet/drain light comes on and stops the wash cycle.I have tried cleaning the water inlet filter, drain pump and non return valve many times, the wash cycle then starts with the pump out of existing water and can sometimes go for about 20mins( sometimes happens a soon as the water starts to flow in) into a cycle before stoppinig again with inlet/drain light on.


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

I own the Siemans SL34A006UC dishwasher which had the recall repair completed. Now it doesn't work right. The unit goes through any of the cleaning choices but when it comes time to drain, the unit stops for a few seconds, swishes water for a couple seconds, stops again, then swishes for a couple seconds, stops and then goes back in to regular cleaning mode until the timer reaches zero. At each drain cycle, it does the same thing earlier mentioned 3 times in a row, then back to washing. The unit


You say "dishwasher which had the recall repair completed." (sic) "Now it doesn't work right" (sic)\015\012\015\012Being a professional I must advise,and that, if this is the case, th ... Dishwashers

I have an Asko w66 front load washing machine that will only wash one way with a 60 second time delay and washes the same way again instead of reversing. At no time will it wash the other way. At the first spin cycle the water is pumped out but the wash drum will not spin. The pump continues to pump and will not stop while the one way wash continues. The timer stops at this point with the one way wash and pump still pumping continuously.


... Asko Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Hello, I have a Frigidaire Dishwasher, model FDB750RCC1. It will not fully drain. There is water in the bottom of the unit after the cycle is complete. As it is not full of water or leaking out of the unit when I open the door I am suspecting it is the pump that has broken? (the water must be draining to the overflow point and then stopping as there is nothing pumping it) Any thoughts or ideas for me anyone? Am I on the right track?


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

Whirlpool ADP 4501 problem. Starts normally andthen after 30 secondes or so begins to 'pulse' ie pump runs briefly then stops and the power 'start' light flashes with each pulsation. No water coming into machine, seems to be trying to pump out but stopping


Sounds like electronic module failure if there is no water in machine. ... Whirlpool Dishwashers

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2112 seconds