Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


Answers :

When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012
\015\012If it did not reset your dishwasher the control board must have failed. Comparing its age it would surely say its control board has failed and must be replaced.
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012\015\012If it did not reset your dishwasher the control board must have fa ... Whirlpool GU2400XTP Built-in Dishwasher

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool APD5550 Dishwasher, cycle does not start, green light on start button flashes 6 times, pauses, flashes 6 times etc. can you please give me some indication what the problem may be. Thanks


... Dishwashers

Nordmende DFSN60 will not select programe,power etc ok.hold programe button and flashes P5 then 55,also EP & 188 flashes,close door and it runs through cycles but doesnt stop .when open door &


... Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

Regarding Maytag Dishwasher, model # mdb4651aww3. Most of the lights on the control panel will not light up. You can't change cycles or set the delay timer etc. You can hit the start button and it runs a perfect cycle, and ends up with clean dishes. You just have no idea what cycle it runs.


I have same problem with my Maytag. Had a repair guy come out and he said it's the 'controller card', not the button touchpanel. The controller card is $127 and not in stock and there's a 'several month wait'. I'm not going to wait, going to buy ... Maytag 24 in. MDB4651A Built-in Dishwasher

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. Th ... Sunbeam SNB542UCAS Built-in Dishwasher

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


... Sunbeam Dishwashers

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Frididair GLD2250RDC0 The lights on the selection buttons (Normal cycle, pots and pans, no heat dry etc) flash when pressed. When the start button is pushed, it sounds like the cycle is starting, but nothing reallyhappems.


Sounds like the very common control panel issue. They have a tendency to short out due to overheating. It is possible it is the motor is bad, you can test power to motor with a voltmeter. If no power, then try power from control panel to motor. If th ... Frigidaire 24 in. GLD2350RCC Professional Built-in Dishwasher

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

The top drawer in the wash cycle after starting will only run three to four minutes and it drops into pause. have to go and push the start button again for the cycle to continue a few more minutes before it drops out. and I have to do the procedure again. The cycle continues where it left off. I had an issue with a missing rubber gasket initially. The service person came out and removed the front, and this is when the problem started. It might be a coincidence. The repair person does not wish to


\015\012\015\012\015\012\015\012If the cycle doesn't complete, or pauses again n again in between then check these:\015\012\015\012\015\012Water-heating cycle\015\012\015\012Many dishwashers heat the wash and/or ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1129 seconds