Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


Answers :

Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Start button pressed - Water loads and "Wash Cycle" lights are on but does not start wash. If "stop/reset" is pressed then all water is properly drained. Tried different wash cycles like "Speed Wash", etc and same problem persists. Have checked interior to make sure no blockage and that washer arm moves freely.


... GE 24 in. GSD6600G Built-In Dishwasher

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

I have a Kenmore dishwasher model 665 15829000 just shut off wont come back on . The lights started flashing when I tried to reset it.Is there a reset button on this model and if so where is it located? I did check the breaker ,to make sure it was"nt that.


... Kenmore Dishwashers

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

MDBH945AWW maytag dishwasher panel lights will not light up. checked breaker and was not tripped. Hardwired circuit. will check tomorrow to be sure power gets to dishwasher. Suspect have panel control failure. In which case should I box it up for the local dump.


These control boards do not have fuses on them. I opened mine up when the front panel touch pad stopped working and the LED indicators were anemic. This is a sign of the ribbon cable connections have oxidized. The ribbon cable connects the touch p ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

Kenmore dishwasher I have a kenmore dishwasher and in the middle of a cycle all my front panel lights went off. I have checked the power going into the dishwasher it is fine. I also checked the door latch it is fine. Not sure what else to check? Same exact problem model number 665.15934 We have had nothing but problems with all of our sears products - highly suggest to SHOP SOME WHERE ELSE before you get stuck too.


Check the continuity of the thermal fuse (part # 8193762). It's clipped onto the electronic control inside the console.Let me know if you need more help. ... Kenmore Dishwashers

Salt Light Cannot get the salt light to go out. Had some problems with a crystaline Deposit on the left side of machine. we checked the inside of the dishwasher and made sure all was clean etc. After that the light wouldn't go out. Had machine serviced. Turns out we were using too much diswashing powder Only need to use about a Teaspoon (heaped) for a wash not the recptacle full.


The sensor in the salt chamber isn't reading properly. Try descaling the machine with solution and restarting. ... Miele Dishwashers

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

My GE Adora wont get the close clean, as a matter of fact it wont even get all of the cloths in the load dry. We have already checked the hoses to make sure that the water is not being blocked in any way at least up to the machine. HELP!! We're starting to stink!


Slightly confused here. Do you have a washer, a dryer or a dishwasher.\015\012\015\012Please provide the full model number to help understand the problem so that I can provide a solution . ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

If i switch on my dishwasher, all lights flash on and off red,and it's makes the beeping noise when it does when the wash is finished... no water is coming in either... please help... it does nothing and you cannot press any of the buttons to use a cycle. it is making a humming noise. i have checked the filter in the bottom of it, and have switched it off at the wall and back on again. cheers,


Un plug it remove bottom drawer. look in back left corner of cabnet on bottom, is it wet dry it out and try again ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1562 seconds