Having problems with your Whirlpool GU2455XTS Built-in Dishwasher ?

Recently we had a powersurge after a powercut, and since my whirlpool dishwasher does not react to the start button anymore, the controller board has already been replaced, but the problem remains the same other control knobs like programme selection are still working.


Answers :

Hi
\015\012
\015\012Is it showing any error code? Notice if the lights are blinking in any particular order. Try turning it off and plugging it back after 2 min.s
Hi,\015\012Powersurges normally blows off fuses.\015\012
\015\012Did you check if the fuse is fine ?\015\012
\015\012wat model is this ?\015\012Did you change the controller board or did some technician change it?\015\012Did it ever work after changing it ?
Repair Help & Product Troubleshooting for Whirlpool GU2455XTS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Recently we had a powersurge after a powercut, and since my whirlpool dishwasher does not react to the start button anymore, the controller board has already been replaced, but the problem remains the same other control knobs like programme selection are still working.


Hi\015\012\015\012Is it showing any error code? Notice if the lights are blinking in any particular order. Try turning it off and plugging it back after 2 min.s ... Whirlpool GU2455XTS Built-in Dishwasher

Kenmore dishwasher model#665 156 0592. detergent cup does not release during wash cycle. after cycle has finished, soap remains in the cup. I did replace the solenoid that controls the latch but the problem still remains.i did receive one response but it was not the answer to correct my problem.


... Dishwashers

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

We have a GE profile dishwasher that will not drain. We have replaced the keypad control and control module and it still will not drain. When we put it in service mode, we can get it to drain that way but when it is taken out of service mode, it goes right back to the same problem.


Its the timer issue:--\015\012what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is common. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Machine does not heat up. The water remains cold and the cycle takes hours irrespective of the setting temp. Heater seems to be OK and a tech guy repleced the sensor today as he thought that was the problem after everything else seemed to checkout ok but still no go. It has already cost us 200 dollars and I dont want to keep spending money having tech guys guessing the problem. Any suggestions? Thanks


Depending on the model, I have had loads of Bosch dishwashers fail because they have blown the heater relay solder joint on the main control board. Usually just requires control board to be opened up, and the faulty solder joint re-soldered. Occasion ... Bosch Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Installed a new control board in GE dishwasher: GLD6860NSS. Still having problems!


... GE GLD6860NSS Stainless Steel Dishwasher

My whirlpool dishwasher is acting up. The control panel lights keeps blinking, I was told by a repain man, that charge me $60.00 to look at it, he said the electronic board was the problem, I order and replace it myself, but it still is doing the same thing, Help Joey


If its the "clean light" then its probably the heater element. You can Ohm out the heater with a meter to check if its got continuity. They had an issue with this where if it wasn't the board it was the heater. ... Whirlpool GU2400XTP Built-in Dishwasher

LE on display panel. I have taken front panel off and all wiring has already been electrically taped together, so I don't think it is wiring. (This was done by a service rep when I had 1E problem) How do I tell if the impeller, rotor or blade is blocked? Or sump assembly or main power control board needs to be replaced?


Http://www.justanswer.com/questions/2bijk-i-have-a-lg-ldf6810st-dishwasher-with-an-error-that-the-serv ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Replaced the control panel on my indesit idl 700 because it was cracked, but still working. since then will not fill with water , water is on switches all seem ok but will not fill. three beeps can be heard , which means its asking for water, what is the problem ?


... Indesit 24 in. IDL700 Built-In Dishwasher

We have a Kitchen Aid model# KUDP02IRBS1 serial# FT1404764 The dishwasher will not work and the "Normal" light is flashing. We have had the control panel replaced once already with this similar problem and it worked for a while. Any suggestions? Thanks for you help!


... KitchenAid 24 in. KUDP02IRBS Stainless Steel Built-in Dishwasher

Kenmore elite dishwasher shuts off after 15 min on normal wash. NO blinking green clean light. I have tried the reset sequence normal wash and heated dry. Did not fix the problem. Control board was replaced. Still shuts off. Pls help.


... Dishwashers

My dishwasher does not work. Only the quick clean-up or rinse only light will come on as well as the Heath Dry button. The dishwasher will not do anything. My husband has replaced the control panel and it is still doing the same thing. What do we do next? Could it be a different problem?


... KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher

Does not dry dishes..still wet and spotty after cycle ..already have replaced control panel..now it reads HE


The reason it would not be drying is because either the rinse aid is low or the heater element is faulty. Not sure why you replaced control panel.\015\012\015\012HE means the heater circuit is tripping. if you are using hot water direct f ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

My bosch shu5315 cycles fine but when finished water is not draining completely. checked screen-cleaned-and problem still exists. Is it the heater? If so how hard to replace?.Note: remaining water fills bottom of dishwasher to point of almost overflowing.


Check your airgap by the faucet of your sink. usually a metal cylinder is the cap. then you might have tabs to press in, or the top of the airgap can unscrew. usually i find stuff in there. mostly fishbones.. otherwise make sure the holes towards the ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

I have s fagor dishwasher model IVF 561AL. Ive been using for the past 6 years. The problem now is there in hot water comin and i had the technician came and got the hearter and timer replaced. Still i'm facing the same problem . Its been weeks and the technicians are still working on it and the the machine is in the warehouse still. Plase let me know what's the real problem.


... Fagor LFA-073 IT Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Problem - water remains inside dishwasher.......about 9 mins before any wash programme ends, washing machine shows E4 and bleeps......water remains inside, dishes clean but slimy. cleaned filters, hose checked, dishwasher cleaner used....still problem exists


... Haier ESD310 24 in. Dishwasher

I get an LE error message on my LG Dishwasher. I replaced the pump. Still get the LE error. Replaced the main control. Still get the LE. No blockage in the pump. What now?


When you receive the LE error code, unplug the machine for approximately 15 - 20 minutes. This will reset the microprocessor.Oversudsing is the main cause of LE error codes. Using non-HE detergents or too much detergent will cause stress ... Dishwashers

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1323 seconds