Having problems with your Whirlpool MDBH979AWS Builtin Dishwasher ?

Dishwasher start button works - Whirlpool MDBH979AWS Builtin Dishwasher


Answers :

Repair Help & Product Troubleshooting for Whirlpool MDBH979AWS Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher start button works - Whirlpool MDBH979AWS Builtin Dishwasher


... Whirlpool MDBH979AWS Builtin Dishwasher

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?


... Whirlpool Dishwashers

Whirlpool dishwasher start button not working...all the other buttons work except the delay and start button - help!


... Whirlpool DU930PWSS Stainless Steel Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

Whirlpool dishwasher gu2400xtpb6 will not start. only a few buttons work. cancel drain button will work for 2min everytime i push it


... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Whirlpool dishwasher wont run has power the cancel and drain button lights up and works the start button does not work


... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

ADP6000WH/ADP6000IX Whirlpool Dishwasher. The controls are not working correctly. When I select the top two (Strong and Normal) settings I hit the start button the dishwasher will not run. When I select the other four (Economy, Rinse, glass and soak) settings the machine works fine. Thanks MB


... Whirlpool Dishwashers

Describe your whirlpool du948pwpq Problem: I have a whirlpool du948pwpq dishwasher in a tenant's unit. They said the delay start button is no longer working. Also, they cannot "de-select" the heated dry option. It seems to be an issue with the electronics of the control panel. I've already tried to "unlock" the buttons - no change. I also powered off the unit in hopes of re-setting - no change. Does anyone have any other suggestions? I am hesitant to call a service person (it's out of warrant


... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher

I have a Whirlpool dishwasher(mod: GU2400XTPS3, SER:FS1617456, TYPE#575-0) ONLY THE RESET CANCEL BUTTON IS WORKING. All other buttons to start washing does not. this just happend 02-12-11. What needs to be done? Can this be repaired? or get another dishwasher. thanks


... Whirlpool Dishwashers

Whirlpool Dishwaher My DWF 416 Dishwasher is nor working, It makes the noise as though it's working then starts to beep and a repative beeping noise and when I open the door the start button is flashing twice, pausing then flashing twice again and on and on


... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Start button does not work on Whirlpool dishwasher # DP940PWPQ2


... Dishwashers

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

Whirlpool dishwasher GU2300 start button wont work


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

I have a Whirlpool quietwash plus 940 series dishwasher that has stopped working. It left water standing in the bottom of it. When I push the button to start it, it makes clicking sounds and acts like it is going through the cycles but it's not working. Model number DU940QWDB3. Any suggestions on what might be wrong with it appreciated. Thanks!


Well, the manual I found online is not free, it will cost you $9.99. http://www.user-manuals.com/user-manual-WHIRLPOOL-DU940QWDB3.html ... Dishwashers

My Whirlpool dishwasher ADP 5340 stops after 5-10 minutes, Start button flashes 8 times. After I press it works for about a minute and starts flashing again


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2403 seconds