Having problems with your WINTERHALTER GS 202 ?

ERROR 4 ON glass wash machine Winterhalter GS 202

I canot fix the error no.4

Answers :

Repair Help & Product Troubleshooting for WINTERHALTER GS 202

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

WONT WASH CLEAN ALWAYS RESIDUE LIKE SAND ON GLASSES ETC. THAT IS ALMOST IMPOSSIBLE TO EVEN REMOVE BY HAND WASH ENOUGH SALT AND RINCE AID ALSO CLEAN FILTER EACH TIME NO OBSTRUCTION IN PUMP FILTER THOUGH HAS AN ORANGE COLOUR SALTLIKE SUBSTANCE INSIDE BRAND NEW MACHINE STARTED WITH BAD WASHING RESULTS AFTER COFFEE PLUNGER WAS NOT CLEANED PROPERLY AND GROUND COFFEE LANDED IN MACHINE ALSO POSSIBLY OUR HOUSECLEANER MIGHT HAVE USED ORDINARY TABLE SALT INSTEAD OF DISHWASHER SAL


Use CLR to remove any build up and then use LEMI-SHINE (walmart in dishsoap aisle) for the cleaning of your dishes. Works great for me as i have the worst well water on the planet. ... Dishwashers

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

I have kelvinator washing machine, E11 shows when on the screen when I start it. ask me to restart the washing machine but when I restarted it disaply error. Any help please


... Kelvinator MDB121RF Dishwasher

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Error lights. When I start a wash cycle machine fills begins to wash then empties, then two error lights flash which are fast and delicate can you explain why this happens and how I can resolve the problem thanks. Terry-ann


This is a Circuit Board that is bad (main control).Do not repair this because the problem returns,and returns. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My glasses are covered in small grainy specs after the wash cycle. THey wash off easily, but that's not good, regardless. I used econo setting & thought changing to regular wash would help, but it didn't. I use Cascade with Dawn (lemon scent, which I purchased by mistake after hearing lemon might damage silver) and a rinse aid. Help. Oh, the model is SHU66C05UC/43, and the machine is maybe three years old. Thanks. Riffi OBrien


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite oft ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Hello! My 3 yr old Bosch dishwasher (I think it is a SHE 43) is doing two things: 1) leaving a serious white film on dishes and glasses 2) leaving grit inside glasses on the top rack (always on glasses placed on the far back right of the top rack) I've tried cleaning the machine with hot washes with no dishes, vinegar only, but no luck. Any thoughts? Many thanks for your help!


Hello. Since you have already cleansed the interior of your dishwasher, we must conclude that the problem is with the water itself. If you do not have a filter on your water, you may want to consider installing a dirt/rust filter, at least on the h ... Dishwashers

We are having a problem with our LG Dishwasher. The machine is washing for about half an hour and then will stop and report an E1 error. According to the user manual this means "Water leakage in Hose connection" or "Water is leaked by damages". We have checked the diswasher's water connections and can't see any water leaking out. We have also cleaned the filers and checked the spray arms but that has not made any diffrence. Any suggestions what this error means and what we can try to resolve it


... Whirlpool 24 in. DU940QWD Built-in Dishwasher

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

The inside of my stainless steel dishwasher has a soap film on it. The same film is now on my glasses. Repeated washing wont remove it. How can I get the film off of my glasses and the inside of the machine? Thanks!


Try running a vineger solution through one cycle. If that doesn't work check the filter at the bottom of the dishwasher where it drains and see if the filter is plugged or partially plugged. ... Maytag Dishwasher

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Hi I have a Bosch dish washing machine. The glasses come out cloady and white when washed. It was perfect in the beginning but it is getting worde. The salt is full, the rinsing liquid is full and set right. I used to use the 3 in one capsules, but now I am trying the seperate salt, powder and liquid but nothin gis working. I have also cleaned the washer with that plastic holder filled with liquid a few times, but it doess/t make a difference. Please help. Melani


First thing to try is to use the capsules and see if they work. Try reducing the detergent a little. ... Bosch Dishwashers

Dirty dishes We have a built-in SMEG machine and it washes 75% of the dishes perfectly. However there is a build up of sandy'ish residue round the inside of the door (mostly on the ledge at the top) at the end of each wash and some of that sticks to the inside of glasses, cups and mugs. Have checked all the filters we can see and they are clean.


Check manual,your water hardness and salt/detergent quantities can make a big difference,theres usually some switches you can adjust for salt/detergent,if not check for partial blockage in pump etc,may be not enough water comming through. ... Smeg 18 in. DWI410 Built-in Dishwasher

Soap problems Not only won't the soap dissolve but there are granules on the inside of my glasses. The dishes are also not getting very clean. I have been using cascade 2 in 1 action packs for a few months now with no problem, they've been great. I ran a wash 2 days ago and when it was done, I opened it up and the dishes were still dirty and the action pack was just sitting there slightly open with detergent sitting on the bottom of the machine. I had done a wash 2 days before with no problem.


Either: 1. not enough water gets into the dishwasher. open the dishwasher 3-4 times during cycle, you should see some (quite some) water at least once, if not - check water valve, water level float and water pressure. 2. the pum ... Kenmore 24 in. 15689 Built-in Dishwasher

We have been using this model since Sept. 2007.When new, it worked very well. It has over time, performed less then we would expect. Not only do we have to scrub dishes by hand before placing them into washer,they some times require hand washing after being washed by machine. Not only are they dirty, the glasses are covered with a cloudy white film. We have not done any maintenance or service to this dish washer. Does this washer require some sort of service or attention. Please advise. Thanks


... Jenn-Air 24 in. JDB1250 Built-in Dishwasher

Machine only in 2nd month of use, the washing powder/tab is nearly always stillin its compartment(compartment has opened), or is lying in the bottom of the machine. The glasses and mugs have bits in them when it has finished.


Either: 1. not enough water gets into the dishwasher. open the dishwasher 3-4 times during cycle, you should see some water at least once, if not - check water valve, water level float and water pressure. 2. the pump is clogged ... Whirlpool 18 in. ADP530 Free-standing Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

The dishes have food residue washed onto them and water spots on all glasses regardless of the amount of detergentinse agent. The pump seems fine there is no water left in the machine after a cycle. any suggestions other than getting a new machine? thank you!


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher malfunction...control panel indicates "IE"...."inlet error"....or water fill error. Machine will not transition to wash mode as a result, even though all the test modes seem to check out ok.


HI. This particular unit is equipped with a defective main PCB board. The solder junction points that hold the relay for the inlet operation are poorly manufactured and soldered. In fact, the entire board is faulty(bad manufacturing). There is also a ... LG Dishwashers

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, ... Bosch Dishwashers

Winterhalter gs502 error b1, fuse l1 was blown, replace now error b1 on machine


... Dishwashers

I have a wash dish machine AEG 80800 sensorlogic The machine can not take water in and there is an error c3. Could you please tell me whats wrong. Kind regards Ulla Jakobsen


... AEG 24 in. Favorit 80800 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1072 seconds