Having problems with your Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher ?

Hi, The union between the hose and the water supply is leaking. The hose pipe seems to be on to the union square and tight, but water is dripping out. Any ideas? Thanks


Answers :

Try replacing the rubber washer as they can perish after a while you can get these from most diy stores.
Repair Help & Product Troubleshooting for Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, The union between the hose and the water supply is leaking. The hose pipe seems to be on to the union square and tight, but water is dripping out. Any ideas? Thanks


Try replacing the rubber washer as they can perish after a while you can get these from most diy stores. ... Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher

Hello i have a Miele Automatic G579, Every time i try to connect the water hose to the tap it never seem to be tight enough as it always leaks, i have a standard tap for UK and the hose connect dose fit just right but always seems to leak ?


Is the washer in the fitting missing? ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Had new kitchen so just re connected my dishwasher. Warning light to check water has come on. hoses and water going into machine seems ok but machine seems to be slow at filling. looked at filters in case of blockage with no result. Any ideas would be helpful please Merry Christmas Janice


I would remove the water line going to the dishwasher and let it run into a bucket. Sometimes on older shut off valves when you shut them off and try to turn them back on they get gunked up or dont open all the way. If you have good water pressure to ... Bosch Dishwashers

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

Kenmore dishwasher M# 665 s#16632000 STOCK# FL4313714 It is leaving about 2in. of water in the bottom once its done with the wash cycle. When I push the drain /cancel button and take drain hose off the sink. It has a small stream but never drains all the water out. Seems to keep the same level. Any Ideas thanks


I would remove the bottom panel of the dishwasher and remove the drain hose from the pump. On some of the Kenmore Dishwashers you can remove the drain spout where the drain hose attaches to and clean. Sometimes something will catch inside the drain s ... Dishwashers

I have just bought a miele 5100 dishwasher, my husband connected it, but the inlet hose connection that goes to the water supply, which has a large plastic piece on it is leaking, you can click it open but it seems ok, not damaged in any way. any ideas or have i got a faulty part, thanks Helen


The big box on the tap end is called the aqua stop fitting. If it leaks around the tread make sure there is a washer in the big nut that screwas onto the tap. The tap might be old and not true on the fase. You could try some thread seal tape on the t ... Miele Dishwashers

I have a hobby 100-1 and the lance is now non effective.The water hoses from the gun quite well but once the lance is attached then no pressure and effectively is a trickle but on occasion it will tend to "spit".Sorry if my description is not very techy but it seems as though the lance has a blockage.Any ideas out there of how to Fix.


... Pressure Washers

I have a model fdb1500lfs dishwasher it has a leak and seem to be coming from the door I have checked all hoses and clamps it has and electrial harness that the water is dripping from


... Frigidaire Dishwashers

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Bought suction hose for karcher in order to use water from bucket. Have attached hose but there is no water being sucked from the bucket . One side of hose attached to washer the other dropped in bucket is this right? The end in the bucket has no suction, and a depressable valve that seems to be impeding the water suction. Do I remove this valve ?


... Karcher 26408500 Pressure Washer 25Foot ExtensionReplacement Hose

No water When the dishwasher is turned on there seems to be no water entering the tub. I checked the water supply hose and that seems to be OK. All the lights are on, evrything sounds like it's working but.....no water ?


HI thanks for your question. i would look at the water valve . located under the dishwasher. remove bottom plate . replace the water valve thanks the appliance doc ... Kenmore 24 in. 15079 Built-in Dishwasher

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The rubber hose from the solenoid to the rectanglar shaped box on the side of the unit where the water goes into the unit. the rubber hose has water comming out when unattached for the side of the unit, however when reattached water gurgles and sprays out of the rectangular shaped box that takes the water into the unit. unit seems to operate fine, just leaks really really bad from the attachement point outside unit.....


... Whirlpool 24 in. DU927QWD Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a kitchen aid dishwasher. The upper spray arm is getting water and getting enough water pressure but wont seem to spin. Ive ran a lot of tests but nothing. ive cleaned out the spray arm and port that gets water to the spray arm. Cant seem to fix it. Any ideas?


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher Spray Arms not Spinning ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have an LG dishwasher that keeps giving an 1E error code. The code means water inlet trouble and recommends the following. Check clogging of water inlet hose(or hose twist or freezing) Check if it's suspension of water supply The problem doesn't seem to be either. ?


Try replacing the water inlet solenoid valve (it may have an open coil). The water line goes directly to it. ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I set up a drip system years ago and now am looking to replace it (old, worn, leaks) but the problem is this-I can't push any fitting (be it connectors, tees, etc) onto the main hose. Both hose and fittings are 1/2''. The fittings in the original system were not near as difficult to use-I also tried hot water (fittings) and ice water (hose), nothing. Is there any size difference between the old and new components?


It's not really a solution-it seems there are two sizes OD (.700", .620") both called 1/2" tubing. The appropriate sized fittings must therefore be used ... Raindrip R333CT Swivel Tee Adapter

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Turn the machine on it makes all the right noises but there doesn't seem to be any water going into the machine. the hose that fills it is ok and water is coming through it . i just dont know where its going once its supposed to come out of the wash bars as they seem to remain dry please help


It sounds as if your inlet water valve or it's solenoid has failed.Please reply with the make & model # of the dishwasher.Thanks!!nc ... Dishwashers

Pump doesnt seem powerfull enough to push water to top rack. i have cleened the filters and checked the pipe to the top rack and there are no obstructions. It is filling with water fine and empting with out problems(emptying seems slow) any ideas?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Kenmore Dishwashers

Turn the machine on it makes all the right noises but there doesn't seem to be any water going into the machine. the hose that fills it is ok and water is coming through it . i just dont know where its going once its supposed to come out of the wash bars as they seem to remain dry please help Jenn Air Quiet Series


Hi\015\012\015\012 \015\012\015\012Thanks for using\015\012FixYa. It means that the water inlet valve has gone bad and needs to be\015\012replaced. Please do\015\012accept the solution if the issue is resol ... Jenn-Air JDB6510 Built-in Dishwasher

Pressure poor After stripping the water side of machine everything seems to be in working order, I have checked all valves and orings and the central water drive. The pressure hose and bayonet orings are ok with no leeks. Everything seem to be ok but still very poor pressure.


... Pressure Washers

Bosch SHU4302 DW has a leak in the bottom left. I cleaned the gasket etc. but no luck. Slow leak drip by drip in the wash cycle. This model does not seem to have the steam vent that other Bosch models have. I can clearly see the water past the gasket on the left, but not the right. But the gaskets on left and right seem to be located identically. Any help in resolving is appreciated. Best Regards


I've got a 4306, and while it never leaked, the bottom door gasket did seem to chemically melt over the years.I replaced it a few months ago. I don't know that a steam vent is needed as the gasketing system never allows any steam pressure ... Bosch Dishwashers

Turn the machine on it makes all the right noises but there doesn't seem to be any water going into the machine. the hose that fills it is ok and water is coming through it . i just dont know where its going once its supposed to come out of the wash bars as they seem to remain dry please help


Your inlet valve has a screen on it.This is probaly clogged, it does happen. At the bottom of your dishwasher ther will be 2 - 4 screws holding the front panels on. UNPLUG FIRST! Remove the panel/s. TURN OFF WATER TO DISHWASHER! you Will have a cop ... Jenn-Air JDB6510 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1113 seconds