Having problems with your Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher ?

Zanussi zsf4123 heating problem

\015 Hi i have changed the heating eliment in my zsf 4123 slimline dishwasher but it still dont get hot at all is there anything else i should look at to cure the problem.I had reasurance from my dealer that the thermastat is combined in the heater. can you help\015

Answers :

Look at the wiring going to the ends of the heater to see if there is an inline thermal fuse that blows when there is trouble in the heater itself. It is about the size of a regular fuse, but may be contained in some kind of covering. It needs to be connected with crimp type connectors, because soldering can ruin the new fuse. Do you have a wiring diagram for this unit? It would help to locate the source of your problem.
Repair Help & Product Troubleshooting for Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Zanussi zsf4123 heating problem


Look at the wiring going to the ends of the heater to see if there is an inline thermal fuse that blows when there is trouble in the heater itself. It is about the size of a regular fuse, but may be contained in some kind of covering. It needs to be ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Hi I have a Zanussi ZDF501 dishwasher that stopped heating up intermittently. It got worse and I fitted a new heater and all was ok for a few months. Then the intermittent failure started again. Note that I tested the old heater and it is actually OK without a short circuit so I don't think it was the problem adn can be re-used. Could it be the thermostat or heat sensor? I am concerned it might be the PCB since the failure was intermittent. Thanks Dave


In my case, although the solder joints on the relay looked poor, improving them didn't help. I had to replace the relay. Fortunately, Maplin stock a compatible one, JM67X for 1.99. See ... Zanussi Dishwashers

No water heating. no drying heating. - Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher


... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Zanussi DCE 5655 heating problem


... Zanussi 21 in. DCE5655 Free-standing Dishwasher

Dishwasher is not heating up water - Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher


... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Hi I have a Zanussi ZD604W which is a built-in model but it is 14 years old so not sure if it is even made now. The problem is that it is not filling with water, everything else seems to be working ie. the element is heating & its making all the right noises!


... Zanussi Dishwashers

Hi, my Zanussi ZSF4123 slimline dishwasher has developed a leak in the front lower left hand side. Not a lot, just a cup full or so per cycle. And not for every cycle. I can't see an obvious problem, doors appear shut properly, and seals look ok. thanks!


... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

KitchenAid dishwasher, Model # KUDP021RBS1 - "Normal and cancel lights blink constantly". I had this same problem about two weeks ago so I googled your site and though the solution I found was not exactly applicable to my problem but I tried and that is - Press high Temp, heated dry, high temp and then heated dry and then cancel button and then close the door. Would you believe it worked like a magic wand. But this same problem resurfaced and I am trying all those old tricks but nothing is worki


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Zanussi ZSF6160 Water not heating


Mantona, you're on the right track. Your heater terminals are large, insulated and poke through the tub facing downward. To test this, remove one of the wires connected to the terminal, then check OHMS. If this is what you did, you don't have to do t ... Zanussi 24 in. ZSF6160 Free-standing Dishwasher

Problems! zanussi zsf6120


You can check the heating element with an ohmmeter and it should read a few hundred ohms. Don't know about the thermostat but it should be inline electrically with the heating element and should ohm as a short when cold. ... Zanussi 24 in. ZSF6120 Free-standing Dishwasher

I have KitchenAid dishwasher model kudmoitjbso. The bottom sprayer works but the upper tray and top of unit sprayers do not. Any suggestion as to the problem and fix? Another problem is heating coil doesn't heat. If something needs to be replaced/repaired, can I do it? Where do i get parts reasonably priced?


... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

ZANUSSI DE6855 DISHWASHER - NO HEAT FOR WASHING OR DRYING


Make sure you unplug before you start. I had the same problem with a DE6850. The heater was ok. Metered at 25.ohms. Apparently, the relay on the control board mounted in the front door behind the switches is a common fault. Remove the screws around t ... Zanussi 24 in. DE6850 Free-standing Dishwasher

My SHU 5305 UC has sporadically heating problems and runs forever. I left the door panel open to put gauges on the red wire (heating) and ran 4 cycles OK; the fifth times there was no heating current


... Bosch 24 in. SHU5305UC Built-in Dishwasher

HEATING ELEMENT IT SEEMS THAT THE HEATING ELEMENT IS NOT HEATING. THIS CAUSES THE DISHWASHER TO RUN LONGER AND THE DISHES ARE NOT CLEANING PROPERLY. I WAS WONDERING HOW TO TROUBLE-SHOOT AND FIX THIS PROBLEM.


Hi\015\012\015\012follow the manual:\015\012http://www.kitchenaid.com/assets/pdfs/product/ZUSECARE/8574093.pdf\015\012\015\012if it dosent work then as you mentioned the heating unit is bad\015\012you can replace it by yourself by buying it and insal ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

Dishwasher zdt 6053 Heating element not working......sometimes!!!! tried all three cicles nothing, heating element not working then its fine again for a couple of washes ????? anyone ever come across this problem, faulty thermostat ,faulty heating element,gremlin in the circuit board?????


... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

No Heat Had the blinking clean light problem, reset, and it fills and runs, but element not heating. Element reads 10.6 ohms, both door switches seem to be making. What else might be causing it not to heat? Is it possible to find a wiring diagram or schematic?


Should be a tech sheet stuck to inside of the bottom toe panel.Switches may check OK with no load applied. There is also an over temperature thermostat that may be open. If all checks OK, control may have failed. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

The heating element stopped heating in my Maytag dishwasher, Model DWU8860BAE. I put in a new heating element, but it doesn't heat.rnWhat might be the problem? What should I do?


... Maytag Dishwashers

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

My Bosch SHY66 does not heat the water. How can I differentially diagnose the heater being the problem from the problem being a failure of the thermal switch?


... Bosch Dishwashers

I replaced the heating element on my Fridigdaire dishwasher, but it still does not heat up. What else can cause this problem?


You have somewhere a thermostat. Most likely that is not working or it is bypassed. ... Dishwashers

Same problem I have the same problem. Just replaced the water heating element because it was split in a few places, also ran a chemical cleaner because we have horrible water, no change.


After changing the heater try to use white vinigare each 3 weeks \015\012apply half a bottle in the washing mashine and set it on 80 degree and run it on the long program \015\012this will make the machine live longer ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0549 seconds