Having problems with your Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher ?

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Answers :

Hi,
\012


\012

I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...
\012
Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

\012
\012kjh;lkhjk

Repair Help & Product Troubleshooting for Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

My chef classic dishwasher is not completely cleaning the dishes. There is no obstruction to the tablet/powder door opening, although there is a small amount of powder left at the end of the cycle. Both top & bottom spray bars are clear & rotate, the water is heating & there appears to be plenty of water getting water into the machine. Drain filters are also clear.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Magic Chef CDB6100 Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have a ADG 450 dishwasher, it has suddenlt topped completing the wash cycle. it runs for about an hour then sits and beeps. If i open the door, the machine is full of water and it looks as though it is trying to spray more water in, thn stops and beeps. If i turn it off and on at this stage and run the rinse cycle, the water clears and the dishes appear to have been cleaned. any thoughts? it happens with all wash cycles.


... Whirlpool Dishwashers

Hello, I have a Kitchen Aid dishwasher, model KUDS30IVWH3. The dishes have not been getting as clean lately, the bottom is decent but the top rack is not getting very clean. Also, when I open the door after the cycle is done, there's a bunch of detergent at the bottom of the door and on the floor of the dishwasher, like it isn't getting sprayed all over or something. Don't know if I have to check the water intake valve or if maybe the sprayers could be partially clogged.


... KitchenAid Dishwashers

Dishwasher, nautilus, doesn't spray water out the top arm? I'm haivng to wash dishes 2 times, and still no better results. I've tried opening the door fast during a water cycle to see which is the problem - can only figure it is the upper arm, the lower arm seems to have water coming out, can't tell if the tower raises completely up.


The jets on the arms can sometimes get blocked with food bits that have got past the filter. This reduces the water flow and rotation of the arms.The arms are easy to remove without tools (they are intended to be removed by the user). ... GE Nautilus 24" Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Water doesn't come out of spray bar. water fills dishwasher (and can drain), it also gets heated. But the spray bars won't spray any water (top or bottom). Any ideas?


There is a pump that sends the water to the spray bars. I believe it is broken. Perhaps there is a jam but I don't think it is possible because the water is filtered before going to the pump. Anyway. The pump may need to be replaced (n ... Kenmore Dishwashers

Dishwasher top spray bar does not spray due to low water fill


Check the water hose going from the sink to the dishwasher to make sure it is'nt clogged, if there's a water shut off valve under the sink make sure it's fully open, also check to make sure the spray arms at the bottom of the dishwasher that supply w ... Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

I have a GE Triton XL dishwasher that is not spraying water onto the dishes. I just reset the power, and that didn't help. Putting it on the rinse only or wash cycle fills the bottom with water, but it sounds like a trickle vs. the spray. The heating element comes on and the soap door opens, but there's not spraying. I made sure there was nothing clogging the water line or other parts. What do you think is wrong?


... GE Tritonr XL GSD6260JCC Dishwasher

Cycle begins and we can hear water filling up, but the arm doesn't spin, and water isn't being "sprayed" around the washer. We can hear the dishwasher "clicking" throughout the cycle, but nothing else is happening, and about 10 minutes through the cycle water just comes pouring out the bottom of the door. There is a bit of a burning smell as well.


... GE Profile PDW8600J Built-in Dishwasher

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Dishwasher i have fixed the fridgadair dishwasher so that i can see what it is doing with the door open; water is coming out of the spinner arms but the arms are not spinning ; it seems that water sprays about 4 inches in air; the top is feed water off and on but not constant.


  This dishwasher does not feed water to top and bottom arms at same time.  It starts with bottom and then after awhile it switches to top and then cycles.  If water comes out arms but arms won't turn,  check all holes in arms.&nb ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Top arm of dishwasher does not spin or spray. it is a 7 yr old frigidaire dishwasher, model #gldb957ab. The dishes on the lower rack also do not get clean. this just started recently. the mid level sprayer will turn by hand but doesn't move during cycles. seems like it would be there is no water coming to the top of dishwasher while it is running.


... Frigidaire 24 in. GLDB957A - Multiple Color Energy Star® Built-in Dishwasher

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

I have a GLD 4456R00CS dishwasher that is maybe 6 months old. It seems to cycle properly, but has never really cleaned the dishes. This is the worst dishwasher we've ever had (over 25 years) and I'm ready to take it to the street. I've cleaned the screen (was already clean), checked the spray bars for clogs (removed, sprayed water through it, and replaced), and looked for any other obvious problem.


Sorry you have had so much problems with this dishwasher. Before you "take it to the street" please check one more thing. I have had so many people say similar problems. \012\012\012\012Check that you are usin ... GE GLD4456RCS Builtin Dishwasher

I have a Whirlpool Model DU850SWPU3. I had this house built and picked the appliances in 2007. I never received any paperwork for the dishwasher and now it doesn't work. Water does not come on when door closes. It sprays a little bit then stops. I can hear it clicking through cycles but it does not spray water at all.


... Whirlpool Dishwashers

Frigidaire dishwasher model FDB857RJS1 not pumping water to the top arm. runs then makes a grinding sound like the motor skipping a gear then back to moving water but not enough pressure to get to the top arm.Unit drains normal runs all cycles but leaves the soap on the door not used.


HI, under the sump housing, there is a major issue concerning the circulation motor. there is a wash impeller that is connected to the circulation motor, via drive shaft and stud. this assembly has been stripped ... Frigidaire Dishwashers

I bought a used GE Triton XL d/w with no manual. It worked great but now it is not cleaning anything, when the cycle is over the soap cup is open but half of the soap is still inside of the cup. I opened the d/w during a cycle and the dishes are wet top and bottom racks so I know it's getting water but the dishes are still filthy. Why is the soap not working? It's like water is spraying everywhere but the door where the cup is!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... GE Tritonr XL GSD6260JCC Dishwasher

Dishwasher The dishwasher detergent door opens during cycle but powdered soap remains in tray. At end of cycle glasses and dishes are wet. a little water is left undrained at bottom. This is a Frigidaire model FDB510LCS1. Checked upper and lower spray arms and they seem ok and pump seems to be working


I have seen this problem before on a couple of dishwashers.\015\012\015\012How are the dishes doing? Are they coming out clean, or do some of them "fail". \015\012\015\012If you rinse the dishes before putting them in the di ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2507 seconds