Having problems with your Zanussi 23 in. ZDi6053SX Built-in Dishwasher ?

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


Answers :

Repair Help & Product Troubleshooting for Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Zanussi zdt6053 in built dishwasher not starting. When pressing the control panel on/off button the 65 deg normal wash light comes on. When pressing the program selection button nothing happens. When closing the door the machine does not start up. Is there a fault in the control panel circuit board? Would water pressure prevent the machine from operating?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Hi, I have the Bosch Logixx Dishwasher . BOSCH SGS0922gb /06 .. aged about 6 years old .... When I press the on/off button 'on' the led display only shows the 'not started' message. When I press the on/off button 'off' the led display lights up momentarily with 'start' etc just before I have fully released the button. I have tried a new switch and the same happens so not that. ALSO i can sometimes see S1....> on the top panel and get the machine to show on the top panel the close door


... Dishwashers

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

WHEN THE START BUTTONIS PRESSED DOWN THE 2 LIGHTS ON THE RIGHT OF THE PANEL LIGHT UP BUT WHE THE BUTTON IS RELEASED THE LIGHTS GO OUT AND THE WHEN THE DOOR IS SHUT THE MACHINE WILL NOT RUN


... Electrolux 23 in. ESL6114 Built-in Dishwasher

Hi, Should I press Start button first or close the door first and then push the start button? If I do the later, I can't see the control panel, although my dishwasher has been installed 1/2" lower than my countertop as recommended by the installation manual. Thanks.


If you are referring to the style dishwasher that has the controls on the TOP edge of the door, you are supposed to select the preferred cycle and options you wish to use, then press START while the door is OPEN. You will then have about 3 seconds t ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I have a whirlpool gold quiet partner iv model #gu2475xtvq and it is not moving from wash to rinse, instead the start button begins to flash as if the door had been opened and needs to restart. Also the control panel button for normal will no longer light up though all the other buttons do. this machine is only 15 months old


Ok I hope child lock is off? And you''ve tried cancel. If yours has the membrane buttons on top of the door, it very likely has water in them. If you remove the bottom kick plate, there should be a service information paper in there. It will tell yo ... Dishwashers

When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA


Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

The start button on KitchenAid model #kudp01flbl6 will not engage, although all of the other lights in the control panel light when pressed. The cancel button will turn off the other lights in the control panel as well. This diswasher is 5 yeras old and lightly used in a household of just 2 professional adults. I've had service come and he uncovered a "burned' conection in the electronic control assembly p/n 8564542, which looked to me to be P8. A new electronic control panel was installed


HI. I need you to clarify somethign for me. You mentioned that you have replaced the " electronic control panel". Are you reffering to the interface board or the actual plastci panel? I understand that the part number "8564542" in in reference to the ... Dishwashers

The hidden control panel has only about half the lights showing what function is pressed. A couple of days ago the washer would not start. The only function which would work was the far left sensor light. After trying to cut power and pushing other buttons, to no avail, we let the machine sit a couple days. It now works again with only half the lights on function pad working. It acts like there was a electrical short.


First retrieve the tech spec sheet behind the toe-kick panel located near the floor and run the diagnostics if it will let you do so w/o the full operation of the keys on the pad,then if it wont the touchpad or keyboard on the front that you use to s ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Dish washer 665.13592K600. Will not start. When door is closed you can hear the click of the latch then a relay on the control board. All buttons work except delay and start. You can push the cancel and drain button and the pump will activate. The start and delay buttons have no effect. Not sure if I have a control board or panel problem.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

The Start button does not light up, yet the left side did light up for wash cycles. I'm guessing the PC Control board has some issue with touch button panel, as a faint high pitched shrill can be heard from the board after I took the door off and put my ear to the board. Also, over time the left side of the panel stopped lighting up too, so I through the circuit breaker. Can you advise which component it is. I'm guessing the faint high pitched shrill is the PC COntrol board attempting to communi


You have a faulty touch pad that will need to be replaced. Below is a \015\012link to a video you will want to download so you can see how to replace \015\012the touch pad.\015\012\015\012\015\012\015\012 ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Whirlpool "Quietflight II" - Will not start. The button for "Delay" works, and the button for "Cancel/Drain" works. Pressing this button will drain the unit. No other buttons will work, however, and the unit will not start. Ideas? I've taken the control panel off and looked at it's guts, as far as I can tell everything looked ok (not burnt and no loose wires), although I am no electrician....


Have you tried testing the control panel with an VOM meter? You can press a button and test the wiring that would go to that particular circuit. See if you get a reading on the specific wire when that particular wire is pushed. Does sound like a cont ... Dishwashers

Kenmore Elite Dishwasher- The touchpad (control panel) keeps going ot and stops functioning. The control board is fine but the start button on the touchpad stops working. If I press it multiple times over and over it will finally engage and kick on. This is my second control panel, can the switch membranes be cleaned somehow?


Jodahabo,\015\012\015\012can you post the rest sequence? i would love to try this!\015\012\015\012thanks,\015\012\015\012the_strum_one ... Dishwashers

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2083 seconds