Having problems with your Zanussi 23 in. ZDT6252 Built-in Dishwasher ?

Zanussi ZDT6252 stops 1min into cycle

\015 I have had a leak with dishwasher and when locating leak had dishwasher in bits and had to stop/start dishwasher to prevent water spilling everywhere. Fixed leak put dishwasher back together but after about 1 minute of cycle dishwasher halts and after about 5 more minutes rinse/hold LED starts to flash.\015\012\015\012Cleaned filters, took side panel off and started a cycle. The following happens:\015\0121. Drains water\015\0122. Starts to fill water, level gets 2/3rds to top of plastic tank on side, whilst cleaning nozzles rotate,\015\0123. Whirring sound from cleaning nozzles stops \015\0124.Water level viewed on tank drops\015\0125. Dishwasher stops \015\0126. Rinse Hold LED starts to flash after about 5 minutes\015\0127. Dishwasher sits like this with water in bottom of cleaning compartment.\015\012\015\012I wondered whether in stop starting the thing I confused it's programme. \015\012Is this possible? \015\012Is there a reset?\015\012Is it anything else?\015

Answers :

You need to reset the computer on the bottom. Had the same problem with mine. The Blinking led means the heating element is bad and will not operate.
Repair Help & Product Troubleshooting for Zanussi 23 in. ZDT6252 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Zanussi ZDT6252 stops 1min into cycle


You need to reset the computer on the bottom. Had the same problem with mine. The Blinking led means the heating element is bad and will not operate. ... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Zanussi zdt6252 stops on 'Rinse & Hold' midway thru Wash Cycle consistently...


The problem here is being caused by Blocked Filters in the Water suppoly In line/pipe. There are two(2) filters in this line, at the water connection point and at the Washer connect point(one at each end). If these filters become blocked, then the re ... Zanussi 23 in. ZDT6252 Built-in Dishwasher

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Zanussi zsf 2400 dishwasher stops in mid cycle


... Dishwashers

Hello My zanussi diva edw1500 stopped working half way through a wash and there is i30 flashing. According to the manual this is some protection against flooding. I thought it was my external drain was blocked and this was stopping the water from being pumped out of the machine. The drains have now been unblocked but when I tried to resume the dishwasher cycle ther same error appears. Please can you advise? Many thanks. Kind regards Jo


... Zanussi Dishwashers

Intermittent Dishwasher fault Zanussi 23 in. ZDT6252 diswasher only partially drains in some of the wash cycles. I suspect it's a faulty float valve & sometimes too much water is taken in at the start of the cycle. Anyone else come accross this??


Fixed the problem by replacing the ELECTRIC ANTI-OVERFLOW VALVE. Simple enough installation - bit fiddly.\015\012\015\012\015\012 ... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Zanussi DW907 Dishwasher stops early in cycle


The heater relay may have gone on the pcb or you may have a stat/wiring fault in the heater circuit. ... Dishwashers

Zanussi zdt100 dishwasher stopped working after interrupted cycle


... Zanussi 18 in. ZDT5052 Slim-Line Built-in Dishwasher

Zanussi zt485 washer stops after first cycle and quick wash light flashys


Maybe its time to check your filters if that does not help then maybe adjust this switch or purchase it. Located behind the kick panel follow link below for a look at the switch.http://www.repairclinic.com/PartDetail/Switch/1036692 ... Whirlpool Dishwashers

Zanussi tempoline not working, son twisted nob mid cycle it then stopped and wouldn't drain. Now not doing anything! Any ideas? I assume its a error code flashing up


The first step of a dishwasher is a drain / rinse drain. I would turn the dishwasher off at the socket, turn the nob to the off position only turn this in a clock wise direction IE: the direction the nob would naturally move. Turn on back at the wa ... Dishwashers

Zanussi DX6453 stops mid cycle and the end light flashes 6 times


... Zanussi Dishwashers

My zanussi ZDF511 dishwasher keeps stopping during the wash cycle & flashes up the code ''20'' - what could be the problem?


... Dishwashers

When I start my Zanussi built in Aquasave zt685 on a normal 65 degree wash it works for a five minutes or so and then stops. When I check, the display has changed to Rinse and Hold. Re-starting it on the quick wash program has the same effect but if I keep re-starting it eventually completes the cycle.


... Zanussi ZT485 Built-in Dishwasher

Zanussi aquasave dishwasher stops at rinse cycle


... Zanussi Dishwashers

My Zanussi zsf2400 has not been cleaning properly for a few weeks, and dishes are often covered in salt deposits. Also the cycle often stops halfway through, the lights go out and it makes a grinding noise. Any ideas?


Problem maybe\015\0121)wash pump blockage.\015\0122)any paricles jam the motor. ... Dishwashers

Zanussi zd501s machine works on cycle until gets to 20 minutes left and then stops and red light flashes


... Zanussi Dishwashers

Door opens mid cycle on Zanussi zsf 4126 slim line dishwasher, thus dishwasher stops running, any ideas what causes this ? Thanks.


CHANGE YOUR SWITCH ASSY (DOOR LOCK ASSY)01179512835 ... Electrolux Dishwashers

My Zanussi DE6744 dishwasher won't run it's cycle since I ran a dishwasher cleaner through it. It powers up then stops and flashes 2 green lights alongside a symbol that looks like a bowl with steam rising from it and an arrow with an upright line to it's right. There is also some standing water in the base of the machine. What do these mean.


The first thing I would do is check the float to be sure it is not stuck in the over filled position. Then I would check the drain to be sure that there is nothing clogged in the drain line. Then I would check to make sure the fill valve is working a ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1236 seconds