Having problems with your Zanussi 24 in. DA6141 Built-in Dishwasher ?

The pump will not turn but when i take off the impellor it will

\015 I see that you can buy the impellor assembly seperate to the motor does anyone know if this is a common problem and should I just buy the assembly or just get the lot\015

Answers :

You would be better getting the lot unless you can actually see damage to the impellor. i would pull the wash motor out to see if anything has jammed it aswell.
Repair Help & Product Troubleshooting for Zanussi 24 in. DA6141 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The pump will not turn but when i take off the impellor it will


You would be better getting the lot unless you can actually see damage to the impellor. i would pull the wash motor out to see if anything has jammed it aswell. ... Zanussi 24 in. DA6141 Built-in Dishwasher

Recently started taking long cycle times, draining pump will not turn off until manually turned off. Pump operates while the door is open.


... Bosch SHX46A07UC Built-in Dishwasher

It leaves about an inch of water after finishing, Hoses seem clear but the pump seems stiff to turn when i take out the filter, how can i get to the back of pump to clear it. do i need to turn the dishwater on its side to get access to it underneath


I WOULDNT TURN IT ON ITS SIDE IF IT HASNT FULLY EMPTIED. I WOULD TRY A DILUTED SOLUTION OF Mr MUSCLE DRAIN UN-BLOCKER. THEN RUN ON A FULL CYCLE STRAIGHT AWAY. ... Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

Dishwasher overflows I have a Maytag PDB3600AWX dishwasher. The pump works well, pumps all water out of the tub when reaching the appropriate cycle state. However, it keeps taking in water when it's not running / turned on (e.g., overnight) and the tub starts overflowing, cuasing obvious leakages (to the basement). What part needs to be replaced? Thanks, C Artz


Sounds like you've got a problem with the water intake valve(s). If it takes on water without water running in the sink, that is where I would look. If it happens when you use the sink, then I would also check your drain hose placement ... Dishwashers

Model G2582 SCVi We have F70 fault displayed. Have turned off water supply but drain pump continues to run even with machine supposedly switched off. Is there a way to stop as it will take 3-4 days to get a service engineer here. Note can't simply throw a switch in fuse box as this also takes out multiple other power ponts


... Dishwashers

Washer is making grinding noise after start. I found little plastic pieces in the filter in top washer drain. Cleaned it all out including the well which turns the rotating sprayer on. Less noise but it was not eliminated. Is it possible that the drain pump is making the noise? If so how do I get a repair manual to take the pump out and replace it?


Hello. Contact the company's US office and request the repair manual Fisher & Paykel Appliances Inc.5900 Skylab RoadCA92647Huntington BeachUSAPhone: 1.888.936.7872 ... Fisher and Paykel DD605HSS 23 in. Built-in Dishwasher

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

Dishwasher filling up and over flowing. switch to turn on pump comes on late or when I manually put pressure on drain. Have hard water and found much scale. could sensor/float scale cause this? Thinking about filling with white vinegar and letting sit so I don't have to take apart. Thoughts?


Take a packet of unsweetened lemonade any brand and run it through a cycle. This will clean all the scale and calcium from the pump and spray arm to improve the circulation of water in the machine. ... Asko Dishwashers

KitchenAid KUDG25SH stopped running, won't drain. Took off upper pump housing, trying to remove 5/16 impellor mounting screw, but it won't turn even with considerable force.


Maybe a peanut or piece of bone stuck in it. What have you been eating that may have gone thru filter trap.\015\012Remove pump and blow back with outdoors hose - worth a try.\015\012PS Was it a peanut? ... KitchenAid 24 in. KUDG25SH Built-in Dishwasher

My dishwasher starts as usual by pumping the remaining water away. Than it starts taking in clean water ... and stops. The arms don't start to turn and the machine just remains blocked. No beeping or anything, just silence. Can I adjust this myslef? Evert from Bologna in Italy


This is the wash motor not running. You will need a engineer to fix this for you. ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

I have a Miele G 892 SCU PLUS Dishwasher. I have clean the filters, check the pump and could turn the impeller both ways. I turn on the dishwasher and it will pump out any water and fill then heat the


... Miele Dishwashers

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Hotpoint BF1620 dishwasher will not turn off only at socket. noise is like the continual pump of emptying dishwasher. tries changing programme, turning on off, keeps turning itself on and pumping


There is a malfunction of the washer controller. Hence the mode is not shifting off from the pump as it does not end the programme. Hence you will have to confirm the output of the controller if the drive is short or functioning by itself. Since even ... Hotpoint Dishwashers

When you turn it on the pump kicks on and it pumps water out of the resivior at the bottom of the washer. It sounds like thats as far as it gets.Does the pump turn on and off buy a timer or is there a float switch?


There is a float switch in the base if you tip machine to the left water will trickle out allowing you to reset machine but if it has a leak you will have the problem return until leak found. ... Bosch 23 in. SHU3307UC Built-in Dishwasher

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

I have a D3100 that continues to pump out. None of the controls seem to do anything, the only way i could get it to stop was to turn of the power point.It does not reset as when i turned on the power point again it started pumping again.


The flood switch has turned on at the base. This means either the switch is faulty or water has leaked into the base of the housing. ... Asko Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1047 seconds