Having problems with your Zanussi 24 in. DA6141 Built-in Dishwasher ?

No water entering machine

\015 I have fitted a new inlet valve, but there is still no water entering the machine. If I put water in manually it works fine, drains fine also.I live in an area where scale is not a problem.\015

Answers :

IT COULD BE THE FLOAT SWITCH ASSEMBLY>\015\012\015\012 PLEASE READ THE FOLLOWING VERY CAREFULLY AS WATER AND POWER DONT MIX WELL\015\012\015\012Before testing the float switch, unplug the dishwasher or shut off the power at the fuse box or breaker panel to avoid an electrical shock hazard.\015\012\015\012\015\012When the water in the tub lifts the float to a set point, the float switch is triggered and it shuts off the water inlet valve, stopping the flow of water. If the float switch is defective, the tub may overfill.If the float switch is obstructed or corroded it can prevent the tub from filling by holding the fill valve off !!so locate, check and clean.\015\012 \015\012To access the float switch remove the lower panel located beneath the door. The panel is usually held in place with two screws either above or below the panel. It may be necessary to first open the door to the dishwasher to reach the screws over the panel, then close the door to remove the panel.\015\012\015\012Note the location of the float in the dishwasher's tub and you will find the float switch beneath it in the access area. The switch has two wires connected to it. Label the wires and connections so that you can properly reconnect them later. The wires are connected with slip on connectors. Firmly pull the connectors off of the terminals (do not pull on the wire itself). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If either is corroded they should be cleaned or replaced. \015\012\015\012Use a continuity tester or multitester to test for continuity. Set the multitester to the ohms setting X1. Touch one probe to each terminal. You should get a reading of either zero or infinity. With the probes still in place, depress the button or lever on the switch and the reading should change to the opposite extreme
The same problem with a Zanussi DWS 694: no water intake.
\012The first thing to try is (after cleaning with hot water and soda until really proper) is to close the water tap and let the dishwaher run for a short while with a closed tap. This releases the pressure from the water tap.
\012Next, open the tap again and let i it run again.
\012You have a fair chance it will take water in again.
\012This procedure releases the overflow safety valve and works only if the cause is removed (by cleaning the dishwasher).
Repair Help & Product Troubleshooting for Zanussi 24 in. DA6141 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SHU43C. I have a leak it seems to come out from the door. I removed the front panel. Inspected the seal and all seemed smooth and not damaged in any way. So I decided to run the machine. Waited for a few minutes and the water leaked from both corners at the same time. The water settled in the rubber trough under the door. After a few more minutes the water leaked over the trough and onto the foor. Is there to much water entering the machine? What limits the water entering

... Bosch 24 in. SHU43 Built-in Dishwasher

Whirlpool dishwasher DU945PWPQ2 four year old machine - never used. Water lines are attached properly and are clear. When dishwasher is turned on the wash cycle light turns on. cycle completes but water does not enter the machine.Water does not enter the machine.

... Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri

... Bosch SHU9915UC Dishwasher

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump

Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate

... Dishwashers

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso

... Dishwashers

I have frigidaire dishwasher,starts cycle,can hear water entering dishwasher,checked level of water,does not get to 1",machine starts washing by the sound of motor, but dishes are not clean,water drains machine turns of,cycle complete.what do you think.

Depending on your dishwasher, it fills either by a timer or by a water probe or float. I will assume its a timer as a probe or float wouldnt exhibit this behaviour. I would say you have a restriction in your water supply line. Check your valves, an ... Frigidaire Dishwashers

Power to the machine, removed the water supply line and there is water at this point but sometimes the water will not enter the machine. The unit is 14 months old.

\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Trouble ... GE Dishwashers

Water not entering machine water connected and going into cold tap but not into machine Internal filter ok Machine pulled out from wall so no kink in ipe

Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Indesit 24 in. IDL700 Built-In Dishwasher

The water enters the machine as normal, as soon as water stops filling, the machine pumps it out again strait away, then bleeps. the whole thing over in two mins. The machine smell awful!. It is a Ikea, whirlpool. Thanks

Change control ... Dishwashers

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


Indicator lights say there is no water entering the machine. The pipe sounds and feels like there is water flowing but it is not getting into the machine itself

If water is flowing, then you should see water enter the DW. You should also feel the water line becoming warm or hot, depending on if metal (copper), insulated metal (copper), or plastic.If the water valve is partially restricted due to accumu ... Fagor LFA-073 IT Dishwasher


... Bosch 24 in. SGS4072 Free-standing Dishwasher

Siemens auto 3 in 1 dishwasher stopped working. lights are on. Machine is humming for a while, but no water enters the machine. Water tap is turned on, filters are clean, no bends in the hose. timer is counting down as during normal washing cycle, but nothing happens

... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Hi there Why is my dishwasher not letting water in? I switch on the machine as normal and all sounds perfect except no water is entering the machine?

The most common problem is with the water valve. It may be defective, and hence not letting enough (or any) water in. ... Whirlpool Dishwashers

De3861fw Hi, the machine stays on the same cycle time(cycle wash 5-84min; cycle wash 6-93min) The machine is on and sounds like it is running, but no water is entering, have checked the obviuos of water being turned on and also draining properly, but to no availe. Please help! Cheers

... Beko Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj

\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

No water seemes to be entering the machine. It

It could be the inlet valve. that is definitely a DIY job. but first i would check out the float inside the machine. if it is stuck in the up position, no water will enter the machine. it will assume that it is already full of water. look for a ... Electrolux 23 in. ESI602 Free-standing Dishwasher

On no programn does water enter machine

... Tricity Bendix 24 in. BDW53 Free-standing Dishwasher

Hi there There appears to be no water entering the machine. Have checked the inline filter + the main machine filters, all clear. Machine all lights up as normal but will not start cycle

... AEG 24 in. Favorit 44050 Built-in Dishwasher

Asko 1716, the program will not advance. I changed the timer mechanism but that had no effect. There is no water leaks and the if i manually move the timer it seems to perform that cycle: water enters the machine, it will wash and will also drain the water out. any clues?

... Asko D1716 Built-in Dishwasher

After dishwasher was started, and water stared to enter the machine, it was unlatched and left with the lever in the open position for some time. The control dial had automatically moved 5/6 degrees clockwise and left there. Now the machine does not want to start no matter what I do. Power is to the machine, latch is moved to the right, but nothing happens. What's next. Thanks for any help you can give.

Hi,\015\012 \015\012After the water stops coming in do you hear a humming noise? If so the motor may be stuck. Unlock the door to disconnect power from motor then turn the motor by hand a few times (should ... Dishwashers


... Maytag 24 in. MDB8750A Jetclean II Built-in Dishwasher

Only a small amount of water enters machine when you start normal cycle. I took off water supply line at inlet valve... screen is clean, water preasure is fine.

You might have a bad water inlet valve, when triggered the inlet valve opens up to allow water to enter the machine, it's usually located behind the lower kick plate in either the right or left hand corner, if it's defective it would need to be repla ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No water entering machine

IT COULD BE THE FLOAT SWITCH ASSEMBLY>\015\012\015\012 PLEASE READ THE FOLLOWING VERY CAREFULLY AS WATER AND POWER DONT MIX WELL\015\012\015\012Before testing the float switch, unplug the dishwasher or shut off the power at the fuse box or breaker pa ... Zanussi 24 in. DA6141 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1209 seconds