Having problems with your Zanussi 24 in. DA6141 Built-in Dishwasher ?

Machine will not initially fill with water so we empty half a bucket into it. The machine then washes and rinses as normal. Any ideas as to problem?


Answers :

Repair Help & Product Troubleshooting for Zanussi 24 in. DA6141 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Machine will not initially fill with water so we empty half a bucket into it. The machine then washes and rinses as normal. Any ideas as to problem?


... Zanussi 24 in. DA6141 Built-in Dishwasher

Whirlpool ADP 5966 Dishwasher using the complete salt load in 6 washes and coating all the dishes in salt that would not rinse off. I filled the salt and 6 washes later it was requiring a new load of salt. We have had the machine for 5 years no trouble The problem is a complete overload of salt coating everything in the rinse water and drying on during the heated drying cycle. The problem is not caused by the following Cracked of failed seals on the lid to salt compartment N


... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

DWI612C wash cycle runs on and on and on. Believing to be a problem with water heating I tried putting a couple large pan fulls of boiling water into machine during wash cycle and this did move it on from wash to rinse. How do I replace the heating element I cant see it it is not in the dish washing compartment? I dont want to call out a repair agent as one can probably buy a new machine for what that will cost. Thank you.


... Smeg 24 in. DWI612 Built-in Dishwasher

Our 2470scvi has caused all of our glassware to turn white. we use very little soap and we always use rinse aid. It seems to me that it is not rinsing properly. It actually has a sound for about 10 seconds that sounds like a motor is stuck.. This sound occurs twice in each cycle. It seems to wash ok but not great of which I would expect for a supposedly top of the line machine. This problem has always happened and the machine is 3 years old.Is this normal for a miele? If so its not the machine w


Hello macit. I do not blame you one bit for being disgusted about this machine. Let's do this. Empty it out and pour in 2 fulll cups of white cider vinegar. Close the door. Let the hot water run into the kitchen sink until it is as hot as it wil ... Dishwashers

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

After washing the dishes in dishwasher everything comes out with a white film on it even the machine the machine has rinse aid and salt in it ive had the machine about 8 years with no problems untill now triciy bendix dh103


... Tricity Bendix 24 in. DH104 Free-Standing Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Dislex dx103wk dishwasher has problem with start up.With door closed and dialed to any wash preset.ei pots for example.with start pressed and both lights onthe machine stays on initial drain setting and will not commence wash.


... Electrolux Dishwashers

Hi, switch underneath our miele g646sc washing machine burnt out. It is situated in a round case, with a polystyrene disc above it. The whole of this plastic case, abour 3" dianeter is clipped under the main body of the machine. Do you know what this one does so that we can try and rectify any problem that has caused the burnout, and any idea of part number or where we can see an exploded part drawing? Thanks! Steve


It is usualy caused by dampness from water in the waterproof tray. the switch is for flood protection.a miele service agent would be your best bet ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Global 450 dishlex dishwasher. Had the handle replaced 2 months ago. After that the ready light did not switch off as before. Now it only rinses. When you set the normal wash cycle the lights for Pre Wash, Wash and Rinse all come on. Pots cycle, the Pre Wash, Wash, Rinse and Dry all light up together, hence the machine thinks it up to that stage of the cycle. Can this be repaired or not. The machine is approx. 12 -14 years old.


... Electrolux Dishwashers

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

About 20 minutes into a cycle (I usually use a rapid wash cycle-P3) the machine makes a loud clicking and grinding noise that lasts for about 1 minute. Any ideas what this could be and how to remedy the problem?


Danby customer service told me that it was built into the machine. The machine would shut off for about 15 minutes after that loud noise occurs. Then would finish the cycle after that point? Got infants, buy one of these products! LOL ... Danby DDW497W 22 in. Countertop Dishwasher

When I turn on machine to start a new wash, it commences cycle and then stops after about 2mins. It would appear it is not taking in water!! Anyone got any ideas what the problem is??


Check the inlet hose and check inlet filter ... Dishwashers

Model #MDB7130AWB Stops mid wash cycle at roughly 60-65 min left, water will not pump out. It sounds like it is about to pump out but doesn't and keeps doing this repeatedly. Using the 8 minute rinse cycle, it drains with no problem...any ideas?


... Maytag MDB7130 Dishwasher

Neff Dishwasher We select a hot wash programme, and when its finished the soap is in the bottom of the machine with some of the items still dirty, others just feel unwashed, i have checked the salt and rinse aid, im using finish as reccommended, the filters are clear, any ideas please


It sound like a detergent cup issue (not opened in time).\015\012The detergent cup itself can become clogged with old dried detergent that prevents it from opening. Sometimes just cleaning the cup takes care of the problem. \015\012Let me know with y ... Neff 24 in. S5543X2 Built-in Dishwasher

I have a Whirlpool Gold Quiet Partner III dishwasher. When I unload the "clean" dishes, there is some type of film or crud on the dishes. I have to hand wash them to get this off. It seems like a lint-type trap might be backing up and then not rinsing the dishes cleanly. Amy ideas what might be the problem? Thanks


You need to check the drain system completely, look for plugged screens, pump impellers, valves and the drain hose. You need to witness a large volume of water flow during drain. ... Whirlpool Dishwashers

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...thank u rate me ... Dishwashers

Integrated Bosch 9000 127 310 (8602) dishwasher. Problem: Although it operates correctly it has just started to make a loud hum during the washing and rinse cycles. It goes quite when draining. Any ideas?


... Dishwashers

Hi I am in an emergency situation with an ikea whirlpool dishwasher. I have no idea what model it is since it's built in and I can't find the manual in my rental apartment. The machine works normally until the part where it's supposed to pump the water out after rinsing. At this point it starts to beep, once, and then 3 times. On and on and on. If I open it, there is water stagnated there. If I try to turn it off and back in, it will go through a whole new program and then I get the same problem


Can you feel the pump operate during the last wash cycles? if not either theres a bad pump motor or lack of power to the pump during that cycle,if this is ok,then remove the drain hose to the main drain to see if this is plugged up with food debris ... Whirlpool GU2400XTP Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Hotpoint dishwasher BFI620 not drained and won't now work: Moved into a new house and acquired a built in dishwasher. First load was fine - or so I thought. Washed and rinsed ok, but large amount of water left in the bottom of the machine which means it now won't work. I've taken out the filter and it appears to be clear, also checked the hose for any kinks, but now I'm stuck. Any ideas?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1676 seconds