Having problems with your Zanussi 24 in. DA6153 Free-standing Dishwasher ?

I have a Technika tdx20s/s/1 dishwasher. It remains in mid cycle and runs continuously. I've checked the cycle motor and all is ok. Your thoughts. Thanks Mark...


Answers :

Repair Help & Product Troubleshooting for Zanussi 24 in. DA6153 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

My lg dishwasher is running ok but i randomly get the LE error code. I noticed that when it runs the cycle it takes 3 times as long to run than normal. Is this the motor or the electronic panel. the wiring is ok already checked.


Motor might have something blocked in the coils. mine did the same thing and found a piece of plastic melted in the motor housing ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

I have a Technika tdx20s/s/1 dishwasher. It remains in mid cycle and runs continuously. I've checked the cycle motor and all is ok. Your thoughts. Thanks Mark...


... Zanussi 24 in. DA6153 Free-standing Dishwasher

Ice maker cannot eject cubes. I took off the front cover and found several contact points for checking the motor, water valve, thermostat, mold heater. There is also a line voltage and neutral contact. Are these contacts live only during certain parts of the cycle? I suspect the heater isnt working to loosen the cubes so they cant be ejected. The motor sounds lilke its running but the ejector is not moving nor is the Gear on the front of the unit. Can someone give me a full description of this t


I usually replace icemakers as a unit. It sounds like the mold heater is out. The system cycles like this: Fill, freeze, mold heat, eject, and start over. The mold heater not working will prevent ejection. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My dishwasher will not drain. When I try to run it through the drain cycle by hitting drain/cancel button it makes one click and nothing happens. I checked for blockages in the drain line and valve but the motor just wont start.


Check to determine if the pump out motor is functional by checking if supply voltage is across the 2 terminals in pump out mode with a AC voltage meter. If voltage is present and motor does not spin this is an indication that the motor is open circui ... Dishwashers

Whirlpool ADG 7550 integrated dishwasher not cleaning properly. Ive checked the filter and there are no signs of blockage. There is no unusual beeping but there is however a weird motor noise that just appeared. Dishwasher appears to run through the cycles but most of the time there is still traces of food left behind. It takes about 3-4 washes to clean the plates. Sometimes there is a lot of soap residue left around the release door which leads me to believe there might be a pump issue? ive ope


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Fagor Dishwasher My Fagor DW suddenly has no water coming in but the motor is running. The cycle starts for about 3 mins then sounds a bit painful followed by all the warning lights coming on and beeping. I live in Spain and am not good with the lingo so am worried about calling anyone out. I've checked the water in pipe which is OK. Help!!!!!!!!!!!! (Please)


Ok if you have a volt meter then remove the bottom kick-plate locate the water valve take the connector off the valve set the meter to ac volts plug the leads into the connector turn the timer to fill if y ... Frigidaire 24 in. FDB126RB Built-in Dishwasher

LG Model LD-05AW2 All motors checked and running, Machine goes through a cycle but main pump not spraying.


Impellers in these often break, will need new pump for easy fix or you could try & replace the impeller ... LG Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

I have a Craftsman power washer model 580 752020. When I start it up, turn on the switch the electric motor runs fine until I either close the trigger to the spray nozzle or press the trigger for power spray. The electric motor just shuts down, if I take my finger off the pressure and let the water run with no presssure the motor runs fine. My question is this. Is the capasitator on the electric motor the probable cause and is there a way to check out the capasitator to see if it is malfuncti


I doubt that it has anything to do with the capacitor on the motor. i think you are having a problem with the actual Motor Drive circuitry. What is happening is when you close the switch, this tells the Motor to "Ramp Up" to pump the water out, what ... Craftsman Pressure Washers

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle keeps running. I have checked the screens and they were clear. I have a Bosch Dishwasher SHU4302UC and I can't figure out how to cancel the cycle it's in. It keeps running and running. It pumped all the water out and the LED indicator are lit for the rinse/dry.


There is a recall on the control board of many of these models. I have written a guide to help. It is here. Look for the phone number near ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.


Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

I have a Kenmore diswasher model 587 1525. I can hear the water filling and rinsing, but during the wash cycle I do not hear the motor. At the end of the wash cycle and when I open the door I see the detergent tablet is sitting on the floor. The dishes are not cleaned. Does this mean that the motor has failed or is it the control card. I can hear some clicking noise while the motor should be running. Maybe solenoids cycling.


... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

My dishwasher motor will not stop running, even after disconnecting the power and plugging back in. It does not run through a cycle with any water, but the motor runs even when the door is open.


... Viking DFUD04 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1172 seconds