Having problems with your Zanussi 24 in. DE6544 Built-in Dishwasher ?

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


Answers :

Repair Help & Product Troubleshooting for Zanussi 24 in. DE6544 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

My dish wash machine (HOBART FX/CV series) is programmed to PO1 and it should be running for short cycle but what's happening is it keeps on running for a long time...please help..many thanks..


... Hobart 24 in. LXIH-3 Built-in Dishwasher

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

My Kenmore Elite Dishwasher (665.16499300) will not fill with water on the Normal Wash. It sounds like it's going through the cycle, but there's no water. I always run the hot water through the tap first. Oddly, the machine operates just fine in the Antibacterial Wash setting. Help would be greatly appreciated.


This machine is known to have a problem with the control panel. You need to get another one and replace the bad one that is in your machine. You should be able to contact sears and see about a replacement. You might even be able to get it done for y ... Dishwashers

I have an equator PLS600 and I can't seem to get it to work. I have tried the WikiFix to help a stalled dishwasher, by adding water and vinegar. When I put on the wash cycle it does not run. Even with the short rinse cycle, the sprayer will not move, and the machine will just run through the cycle until it starts to drain. Please help!!! Thanks =)


Give the spray arm a spin to make sure it rotates. It should spin freely. If not, remove plastic spray arm clip, flip it over, replace it, and try again. Make sure holes in the spray arm are clear of debris. Spray arm must be clean for it to spin ... Equator 20 in. PLS600 Free-Standing Dishwasher

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Dishwasher runs full cycle, however, the dishes and glasses have small particles of food dried on them when done. I do rinse all plates and utensils before turning on. I run on a normal cycle, no heat dry. I use cascade action paccs 4X concentrate. Which appears to not disolve completey, the packet. It normally does. There is no water back-up in sink, and I also open the trap ,no blockage. Please help, Dan


Hi Dan and welcome to FixYa, I am Kelly \015\012\015\012 Most of the time when you start having dirty dishes post wash there is either an internal blocked screen under the lower wash arm tower or a problem with the drain. ... Dishwashers

Fisher & Paykel single SS Dishdrawer. Cycle's stuck. Normally sticks at 137mins and 33 mins, has stuck on other times too but it's always on those times. Have tried pausing and opeiong the drawer int he hope to kick it back into working but doesn't help. A normal cycle of 151mins is taking 4 hours.rnI normally have to let the cycle run till it sticks on 33 mins then I trun it off letting the dishdrawer empty and kick into dry mode. I hate to see my next electricity bill, its been a month n


My dd603 takes 3 hrs to do a 55 minute cycle-who can help me ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

After starting the cycle, the dishwasher starts and runs normally for a short time, then the water drains out of the tub prematurely while the cycle is still going. The machine then runs dry until the cycle times out. At the next cycle and the process repeats. It started as a sporadic problem, but is getting worse.


You may have a faulty drain valve,the drain valve is under dishwasher there are two clips on each side check,with applance store for replacement part. ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

My Kenmore built-in dishwasher is running its cycles normally, but no water is coming into the machine so it runs the cycles dry (even a rinse cycle). Can you advise? If a part is needed, is it an expensive one? Thank you!!


Sound like the inlet water valve is to blame here - or else the main controller board relay is not telling it to open. Further testing will be necessary to determine which is the cause.If it is the board - you are better off getting a new ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

De3861fw Hi, the machine stays on the same cycle time(cycle wash 5-84min; cycle wash 6-93min) The machine is on and sounds like it is running, but no water is entering, have checked the obviuos of water being turned on and also draining properly, but to no availe. Please help! Cheers


... Beko Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a dish washing machine bauknecht model gsx 7988, when closing the frontdoor, the pump starts to run and a beeping sound is noticed, this beeping sound and automatic running of the waterpump happens on any selected program, when opening the door, the grren startligt is flashing two times fast,then a halve a second out and then flashing again two times fast etc.etc filter is clean, waterpressure is ok, eno other program can be started.pls help.


... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

We just installed a new kenmore dishwasher yesterday. Model 13242 It has been running for almost2 hours and is still on the washing cycle--no water in it however--is this normal? I'm in a bit of a panic as we are canning and I need the jars washed--we didn't get a manual with it as it was a floor model so I don't know how lon the normal cycle ids. HELP


THAT IS NOT NORMAL!!!!!!! A normal wash and dry cycle will take approx. 2 hours in length including drying cycle.\012You should see that water has been present in the machine within the first 2 minutes of the start of the wash cycle, you shou ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1360 seconds