Having problems with your Zanussi Dishwashers ?

Will not go passed pump out stage at begining of cycle


Answers :

Thrown it out. No help needed.
Repair Help & Product Troubleshooting for Zanussi Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will not go passed pump out stage at begining of cycle


Thrown it out. No help needed. ... Zanussi Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Hi. IKEA Whirlpool DWFA10 dishwasher.Firstly, when switching on the machine to befin the programme the machine does not pump residual water away.It then begins its cycle (in this case the pre-rinse cycle).After 12 or so minutes,when the cycle finishes and the water should be pumped away,the machine stops and the green warning light keeps flashing 4 times intermitantly.


... Dishwashers

Dishwasher makes very loud noise when running - my guess is pump or motor....only 2 year old - very disappointing. Makes lud sounds at beginning of cycle and then several times during the cycle. How can I tell if it is the pump or motor? Thanks


Maybe something in pump or bad pump baring ... Bosch Dishwashers

I have a Bosh SHU3302UC dishwasher that seems to be pumping all of the water out of the basin and will not advance to the next cycle. I know it is normal for the washer to pump to the drain at the beginning of the cycle, but this unit will not advance. Any thoughts??? Thank you, Matt


Make sure you go to the Bosch website and follow the recall notice on this model...they have a recall repair notice that replaces the faulty controller on this model...the faulty controller may cause a fire so be sure to stop using the unit until you ... Bosch 23 in. SHU3302UC Built-in Dishwasher

Dish washer is seldom used , maybe twice a year. Notice during a drain cycle that the pump makes a squaling noise.This happens only after the load of the water has pass through the pump. The dishwasher is a boush,is there impeller style pump? Maybe dry rot ?


The pump impeller is probably plastic -- if so, dry rot is out.\015\012\015\012Most likely the pump shaft is just dry from lack of use. More use will probably wet it enough to stop the squeal.\015\012\015\012Charlie ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

I have a Bosch 2046 UC DW. When you try to start the cycle you hear the timer clicking. The knob slowly rotates to where it should start the cycle but stops there and won't start the operation. If yiou advance the knob it opens the soap dispencwer but the pump or cycle will not begin gerald qually


The programmer is faulty, effectively worn out, and needs to be replaced. You may be able to service the mechanical parts of the programmer by cleaning and lubricating it and possibly by replacing the springs but it's just easier and less time consu ... Dishwashers

Pump does not start at beginning of cycle during water fill. If I open the door and close, the pump starts. Also soap dispenser doesnat open.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the pump won’t start it is most\015\012likely the pump that has gone and you have to replace it. If th ... Whirlpool 24 in. DU927QWD Built-in Dishwasher

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

We have a Bosch SHE45M06UC/50 dishwasher that is acting a bit nutty, first of all the timers are all wrong, mostly too short for what the manual says except the quick cycle and it is too long. There is on some cycles a very long delay before it begins to fill and it seems to alternate between pumping and running randomly


Hi,\015\012\015\012The first thing to note with your make of D/W is the display only shows "estimated time" not actual time. There are just too many variables to give actual times, i.e. water temp. at inlet, drain hose length & diameter, as well as p ... Bosch Dishwashers

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

Whirlpool DU8900 XT-5 the water comes in at beginning of cycle and the heater heats the water, but the machine does not go any further. it kinda' hums but no water gets pumped and moving. at end of cycle the water stays in the tub.


If you can hear a low humming noise when it should be pumping water round, then suspect the circulating pump.\015\012fault can be motor capacitor - low cost part\015\012or\015\012pump seized - see if you can turn it by hand ... Whirlpool Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

I have an ASKO D3250 and it has recently started making a loud noise from the pump area. It starts as soon as the cycle begins and doesn't stop even if you open the door. It seems to stop about 90 seconds into the cycle. Noise is best described as a noisy solenoid but could also be some sort of actuator that is stuck. What part is the problem?


All power and sounds should stop when any dishwasher door is opened.Your door switch may be stuck causing it to continue.The 90 second sound at the beginning of the cycle is the water pump extracting any residual water before taking on cl ... Asko 24 in. D3250 Built-in Dishwasher

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

I have a Kitchenaid KUDK03CTSS2. It goes about half way through the entire cycle, let's say half hour in and then it sits there buzzing/droning for at least 30-40 minutes, then it finishes fine. Had a service guy in and he would't wait for the symptoms to appear. Everything is good at the beginning. He replaced the pump motor, didn't find any debris in the unit. But it's still doing the same thing.


Turn the dishwasher off about 20 minutes after it starts the droning/ buzzing and feel the water temperature.\015\012\015\012Also run the dishwasher in a short cycle where it uses cold water only and see if there is any difference.\ ... KitchenAid Dishwashers

Neff s5443x1gb/07 drain pump starts at beginning of any cycle then stops. when due to fill with water nothing happens and the end light is flashing. there are no blockages. is there ant way to check the supply hose which is in one with the valve or could it be something expensive?


... Neff 24 in. S5443X2 Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

Drain pump continues to run even when door is open. won.t allow new cycle to begin


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Siemens SL85A705UC 24 in. Built-in Dishwasher

At the begining of the wash cycle the pump drains any residue water but it does not seem to detect that all the water has gone and eventually comes up with error 20 code. The waste pipe is not blocked.


Base of machine flooded, meaning you have a leak. Pull machine out and tilt machine to one side to release water and try again\015\012Faulty pressure switch. ... AEG 24 in. Favorit 40850 Free-standing Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1241 seconds