Having problems with your Zanussi Dishwashers ?

HI I HAVE A ZANUSSI ZDF221 DISHWASHER THE WATER WASN'T GETTING HOT ,SO I FITTED A NEW ELEMENT BUT IT IS STILL THE SAME ,ANY IDEAS WHAT IT COULD BE MANY THANKS ALAN GRIFFITHS


Answers :

Hi the most likely cause is the electronic mounted in the control panel behind the progamme dial. there is a relay which can unsolder itself. you can try resoldering (use lead free solder). or change the electronic.
Repair Help & Product Troubleshooting for Zanussi Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HI I HAVE A ZANUSSI ZDF221 DISHWASHER THE WATER WASN'T GETTING HOT ,SO I FITTED A NEW ELEMENT BUT IT IS STILL THE SAME ,ANY IDEAS WHAT IT COULD BE MANY THANKS ALAN GRIFFITHS


Hi the most likely cause is the electronic mounted in the control panel behind the progamme dial. there is a relay which can unsolder itself. you can try resoldering (use lead free solder). or change the electronic. ... Zanussi Dishwashers

Hello, Firstly, thank you for what you do, you help so many people and I know it takes time. I have a Bosch SHE44C06-UC Dishwasher. I fixed the E1 (Heating Circuit) error. First, before I found the writeup about the solder joint, I bougut a new heater and replaced it, ithe part included the element, flow switch and high temp sesor soall are new, then I fixed the solder and E1 went away and the cycle finsihes and the dishes are clean and dry. Still I check the error codes and still have


... Dishwashers

Like so many others, I am experiencing a problem with my GE dishwasher's smartdispense. I have ALWAYS used the SAME detergent(Cascade Complete)and still have the gumming-up issue. I noticed that the dishes were not getting clean and when I opened the smartdispense cover I could see that the detergent was gelled. Spent the better part of 2 hours trying to remove as much gunk out of the dispenser as I could with the help of a plumbers flexible plastic drain cleaning tool. This really angers me as


I had the same problem as you also using Cascade Complete. It turned to a wet solid and completely cloged up. I have spent 3 days cleaning it and now have it working again. I had to spoon out what I could, but the purge method still would not wash ... Dishwashers

I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?


Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers

Powdery residue on some dishes, will not wash off. Repairman said it was due to warter temp, but have tries heat & Anti bacteria and still persists. Could it be chemical build up because I was using a no phosphate detergent(Finish)? Repairman also suggested I use Citric acid to clean dishwasher tub and element. Could this just be hard water?


Hi,Check your heating element.. Dishwasher ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

My dishwasher has just satred leaving a white haze, almost a dust on the dishes. This especially bad on plastic dishes. I took it into a repair guy and he said my element was causing this. After spending $140 for a new element and waiting 3 weeks I still have white dust. What else could it be?


HI. This is actually the result of a high mineral content build up that is occurring inside your unit. This can be corrected by using a highly concentrated dishwasher cleaner. Calcium build up will cause this mo ... Frigidaire Dishwashers

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

Changed element on zaussi zdt6244 dishwasher but still cold what could be wrong?


... Zanussi Dishwashers

Matsui MF160 dishwasher is running programme but is cold. All lights etc are on as normal, beeps at end of programme. I have replaced the heating element, but it is still cold. Any ideas?


It sounds like there is a short somewhere in the line running to the heating element. You probably did not need the replacement, and hopefully can return the one you got. I would trace the wires from the heating element if it was me personally, unl ... Dishwashers

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...thank u rate me ... Dishwashers

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

OE Error on LG Dishwasher model LD-14AT2. Filters arent blocked and chord not kinked. Wont stop pumping water out in wash cycle. Seems to think there is still water in there when there isnt any at all. Any ideas as to what could be wrong?


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

I brought my 2 yr old Kitchenaid model kudp01dl over from my foreclosed home to install where I live now, and the left side of the touchpad to run a load doesn't work anymore. I know one wire had jostled loose underneath, and my husband re-connected it to it's terminal, but could there be another I am not seeing as well? Or any other ideas? It still works fine to cancel, drain, and select drying options, etc, but I can't start a load!!!


It Is SOMEWHAT Common for WIres / or PLUGS to Come looes on Apliances Your Husband May need To Remove A Pannel and Thourelt INSPECT FOR this what you DISCRIBEVARY WELL MAY BE AS SIMPLE AS 1 WRE OR EVEV 1 PLUG OR WIRES THAT IS DISABLEING THE UNIT FROM ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Hi, my dishwasher stopped heating the water so we have a replacement element fitted but the problem still persists, what could be the problem?


If the dishwasher completes the cycle but does not heat the water then it is likely the thermostat is the problem. (since you say you have fixed the heater).\015\012\015\012If cycle is not completed and water remains at the bottom and the ... Kenmore 17459 Free-standing Dishwasher

Got a Diplomat ADP8322. Starts Cycle then starts bleeping 3 flashes which is a heating error. No hot water at all. Had a look and cleaned watr pressure switch still not working. Any ideas has the heating element gone.


Possibly heating element - only way to find out is to check continuity with a multimeter.there is also a thermal cutout in series with the heater which could also have gone ... Dishwashers

Zanussi DX6452 not heating up, replaced heating element but still no joy-please help!! What else could I look for?


Could be an element fault but check the pcb tracks on the main pcb that \015\012go to the heating element as this is a common fault/issue. track will be\015\012 blown around relay connection as a rule. ... Dishwashers

Hygena ahy-8122 the machine switches on starts wash cycle then trips rcd in home fuse box.trips somwhere between cycle 2 & 3 .have isolated & dissconected heating element but still trips rcd.any ideas?.thanx


... Dishwashers

Just purchased and installed the LG LDS4821 dishwasher, instantly got the OE error code when we tested it. After following troubleshooting tips and calling customer service, error code still not resolved. Hose is not kinked, hose is not clogged (as no dishes have even been washed in it), and it's level. Does anyone have any idea what we could do to fix this problem?


Try a test cycle with the end of the drain hose placed into a bucket. If the dishwasher does not pump out then, call for warranty service (In the US, find a ... LG LDS4821WW 24 in. Built-in Dishwasher

Kenmore dishwasher model 363.1410691, approximately 18 yrs old... Wash cycle was on, unlocked and opened door to add silverware, shut and locked the door, but water did not (and will not) come back on. Appears heating element and timer still works...any ideas?


Check your water valve. if know water goes in normally that is the culprit. disconnect the wires and ohms it out with a ohms it out. if this works then you can help me by sending me a 4 thumbs up post thanks! ... Kenmore Dishwashers

Indesit idl 535 dishwasher not heating up,I have changed heating element and tested all connections and still not working,any ideas


Hi,did you find out what was wrong with your dishwasher,as i have the same problem.steve ... Dishwashers

I have a pressure washer with a faip 3 piston pump. the other day i was using it and it stopped unloading. i cleaned the unloader and it didn't help. I bought a new one and it still won't work. I e-mailed Ryobi and they will not respond. There were no instructions on installing and adjusting the unloader. Could you give me an idea how to install and set up the new unloader. Any help would be most appreciated.


I think your main problem is that the unloader valve needs to be lubricated. Use the very best water resistant bearing grease you can find. If you can e-mail me a pic of your unloader assembly I can try to explain how to set it up. [email protected] ... Honda Pressure Washers

Hi I have an older model Gaggenau Dishwasher (10-15 years) and during the wash cycle it seems that the water stops and the element heats up red hot? Any ideas on what could cause this problem? Thanks


... Gaggenau GI976-760 Built-in Dishwasher

I changed the handel and switch assembly on my dishwasher because the old one was broke.The dishwasher does not turn on. It still doesn't work. it doesnt even light up. although one button does glow a little. Do you have any idea what it could be? the model number is MDBH955AWB


Check for line voltage at the door switches and from there to the control board thats to the right of the door latch switches for line voltage,if you have line voltages in all these areas then replace the front membrane push button control panel that ... Maytag MDB9600A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1095 seconds