Having problems with your Zanussi Dishwashers ?

Hi my Zanussi ZDF 511 dishwasher doesnt heat the water. I have changed the water heater but the water remains cold. Any ideas? Ian


Answers :

Repair Help & Product Troubleshooting for Zanussi Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi my Zanussi ZDF 511 dishwasher doesnt heat the water. I have changed the water heater but the water remains cold. Any ideas? Ian


... Zanussi Dishwashers

Model # gsd3320c04bb. I am getting water to the inlet valve. I tried changing the inlet valve but still no water goes thru it. I am getting 22 V AC at the connector when operating. The only water that is circulating in the dishwasher is the water that is remaining in the pump system. Any ideas as to what is preventing the inlet valve from operating?


Sounds like you need to replace the mixing valve which is where your incoming water lines connect to the back of the washer. ... GE 24 in. GSD3320 Built-in Dishwasher

Lack of pressure in a karcher 455. motor powers on changes sound as trigger is depressed but water remains at mains pressure. oil replaced and had no water in old oil. any ideas.


Most cases the engine is used on many different units find one of those for a pump ... Karcher 4.550-620.0 pressure washer part 45506200/4.550-620.0

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Hi I have a Bosch SGV46M13GB Classix dishwasher. Total cycle time is far greater than the displayed time and the water doesnt appear to be getting hot. I've checked the control board for any dry joints / damage etc - Nothing evident. Is there a wiring schematic available so I can check the voltage to the heater to confirm its the heater thats the problem before I purchase spares. Also, if I need to change the heater - Is there any guidance anywhere ?


First thing to do is check and make sure that it is connected to the hot water line. ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I've got a hotpoint bf168 dishwasher,been working fine until y'day when nothing washed, realised there was no water coming into it. Change water inlet pipe but still nothing, I can hear water going thru the pipe but then just seems to empty itself. Any ideas guys .


Hmmm.... could be the controler. or a stuck valve... have you tried to reset it? turn off power and turn it back on... ... Hotpoint 23 in. BFI68 Built-in Dishwasher

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own wat ... Bosch SHX46A07UC Built-in Dishwasher

Dishwasher not working. Two weeks ago the heating cycle didn't switch itself off but appeared to correct itself. Now there is no water in the cycle... pump and heater working, just no water reaching the arms of the dishwasher. Any ideas why?


Sounds like a bad pump. If it drains the water and doesn't deliver at arms the pump is more than likely bad. First of all pull the water supply line off and see if there is build up from hard water on the in-line screen (if present), then If you are ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Beko DE 2541F Slimline Dishwasher and it fills and empties the water but the cycle does not start. The water does not get to the spray arms. I have tried on pre wash cycle as well so I do not think it is the heater element. Any Ideas


If there are no problems of drain valve stuck, then the problem with the micro controller board.When the water is full in the tank, the wash cycle will start with the spray arm in action. Lastly block the drain hose and see. Here water fu ... Beko 24 in. D3731F Free-standing Dishwasher

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

Cloudy Dishes This condition suddenly started after couple of years. Water heater is 7 yrs old, never drained, therefore I think this could be the problem. I am going to drain it and report. I do have a whole-house water filter which I change out monthly or every other month. My guess is that without it, this problem would have surfaced long ago.


The problem is hard water. Go to www.dishwasherfilter.com and get their new product. It filters the water and takes out the hard minerals that cause spots and clog di ... Amana 24 in. ADB2200AW Built-In Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Beko dishwasher DE3431FW washes and goes through cycle but does not heat water,ive changed heater element and changed pcb. new pcb does not turn on machine? old on does.changed thermostat.what could it be?


... Beko 24 in. D3731F Free-standing Dishwasher

We have a Whirlpool ADP962 Dishwasher that will not fill. I replaced the inlet hose as I thought the solenoid was faulty. It's gone a step further and now sounds like it fills (continuously) however it soon drains without any water entering the dishwashing compartment (this remains dry). I believe this issue was caused by running it through a cycle without the water mains turned on. Any ideas?


Hi.When you say inlet hose I think you are referring to the inlet valve, which has a built in solenoid. The inlet hose is only the rubber hose connected to valve and faucet.Rather than the hose the problem is likely overfill d ... Whirlpool 24 in. DP840D Free-standing Dishwasher

I have a GE GSD2000J01WW Dishwasher in a building with low water pressure. The inlet hose is 3/8" OD. The heating coil gets too hot and gives off a bad odor as there is not enough water at start up. Is there a way or a replacement part that can be used to change the timing of the heater and wash cycles, etc.? Thanks


... GE GSD2000J Dishwasher

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

Dishwasher starts to fill but has very little water in it when cycle starts. disconnected float switch and does not change the operation. water never fills to cover the heater.


Hi,There are ONLY 2 things that could affect this :-\015\012\015\012 \015\012 Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\01 ... Kenmore Dishwashers

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

My bosch shu5315 cycles fine but when finished water is not draining completely. checked screen-cleaned-and problem still exists. Is it the heater? If so how hard to replace?.Note: remaining water fills bottom of dishwasher to point of almost overflowing.


Check your airgap by the faucet of your sink. usually a metal cylinder is the cap. then you might have tabs to press in, or the top of the airgap can unscrew. usually i find stuff in there. mostly fishbones.. otherwise make sure the holes towards the ... Bosch 24 in. SHU53 Built-in Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

Dishwasher hey! i have a frigidaire dishwasher. turns on, fills up with a little water and just sits there for about 10 mins doing nothing. starts to clean then nothing some more. it drys everything but leaves the dishes totally filthy even though they are well rinsed prior. after they are dry, the dishwasher then pushes out the remaining water like it is supposed to and on into the disposal. any ideas? i cleaned the pan out completely and replaced the lower parts. thanks!


DEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\0 ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Any of the programs start ok (water enters etc..) but the program does not move on, will stay at the same place early in the program cycle for hours. You can move the program on manually and the water ext will exit but the dishes are not properly washed. Changed program timer switch but still same - zdi6041x dishwasher - any idea why ?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Zanussi 23 in. ZDI6041 Built-in Dishwasher

I have an AEG OKO 4040 Favorit which will not perform the main wash cycle. Water fills ok & pumps out ok. Heater element is working fine. any Idas


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1698 seconds