Having problems with your Zanussi Dishwashers ?

Dear Sir. I own a Zanussi dishwasher ZDIS 102. i have been using it for more than 2 weeks and i see a phenomenon which i didn't find the Answer in the manual and even in the place where i bought it. i place the dishes in the dishwasher and after 5 minutes the lights on the control panel began pulsing. it does not exist any of the problems said in the manual. firstly i thought it was an electrical problem (in case the voltage is low). please can anyone tell the reason of the pulsing and what it


Answers :

Repair Help & Product Troubleshooting for Zanussi Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dear Sir. I own a Zanussi dishwasher ZDIS 102. i have been using it for more than 2 weeks and i see a phenomenon which i didn't find the Answer in the manual and even in the place where i bought it. i place the dishes in the dishwasher and after 5 minutes the lights on the control panel began pulsing. it does not exist any of the problems said in the manual. firstly i thought it was an electrical problem (in case the voltage is low). please can anyone tell the reason of the pulsing and what it


... Zanussi Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

Hi i have a Candy CDI 1012/B Intergrated dishwasher and 4 lights are flashing during the first programme then system drains and stops showing four lights lit. We have no instruction manual or service manual this would be good to get hold of as we have serveral of these machines. any idea what the problem is to save us time investigating it. Thanks Paul


Hi. The four leds flashing quickly at start of the cycle means that there is an inlet problem. Check that the inlet hose is not bent, blocked or kinked, ensure that water has sufficient pressure. The inlet valve can be tested reading Ohms at valve te ... Dishwashers

I have a GE Profile Dishwasher (PDW9200N00WW). A red light for the smart dispenseer of soap just appeared in the status area of the control panel (to the left of the reset/start button). I could find nothing in the manual addressing that and I recently refilled the soap dispenser. What does the red light mean and why doesn't the red light go off? I only had enough soap to fill it halfway and will get more to completely fill it. Is that the problem--only half full?


... GE Dishwashers

Kenmore Elite 13133K started to fill, the door was opened. Now it won't resume, drain or fill, the geen light is flashing. I turned the power supply off for 5 minutes and the problem still exists.


... Dishwashers

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

Model Karcher 320H 1.141-205 When first switched on the pressure builds up and then the machine keeps no switching on and off, opening the trigger on the lance and it works ok, close trigger and the pulsing starts again, if left like this it would probably burn the motor out. I have lubricated the brass/plastic piston the operates the on/off switch but problem still exists. I have also opened the pump chamber but cannot see any debris or problems with the rubber seals. Any help would be most app


... Karcher 1550PSI Pressure Washer

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Brand new Miele 2170/2180 dishwasher. First time we try to use it, it stops after a few minutes, the warning beep beeps incessantly, and all of the program lights are flashing. According to the manual, we should turn it off and on and then try again, which we did. The problem persisted. The manual says that this may indicate "a technical fault" and we should contact customer service. Unfortunately, they are closed for a three-day weekend. Any suggestions?


It is just possible you have a problem with the drain.if you plumbed the drain to a spigot on the sink trap, did you make sure the spigot is not blanked? the sink spigot will be blanked if it has not been used before to stop water from the sink ... Miele Dishwashers

Thor dishwasher Model No. D3764FS purchased in 2004, can't find users manual and have a problem ... A red light is showing up on the control panel just above a symbol that looks like a element ???? Have tried on the internet for user manual but had no sucess... Are you able to help me... thank so much


... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

My SHE43 Bosch DW will not pump the water out after the last cycle. The service guy said the Door latch was broken and replaced it. but the problem still exist. He now say that the water lines are freezing up because the DW is on an outside wall. The Thermador DW that was replaced never had this problem during the 15 years it was located in the same place. Could this be a bad design? Help!!!


I\015\012\015\012\015\012\015\012 the water doesn't drain from your dishwasher, check these:Drain line/air gap ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Hi, i have a Miele G 693 SC plus which had the red light lid up: evacuation problem or entry of water, how can I solve this problem ? Furthermore I have tried to download a manual to try and find a trouble shooting diagram, I have spend an hour through a site "devicemanual" without any luck, Does Miele have a simple site ? for this, thanks - Peter


Hi,this is a general fault light which could mean anything without a Miele Technician coming out and connecting a laptop ... Miele G892SC SS Dishwasher

Clean light is blinking. Manual says itis a malfuction and problem with heater circuit. How do I know if the problem is the heating element or a sensor?


Press "Heated Dry" then "Normal Wash", then "Heated Dry" again then "Normal Wash" again (4 button presses). This fixed it for me. ... Whirlpool GU2400XTP Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Whirlpool DU900,09,10,11,15,20,30,DUL100 Hi, I'm not sure what exact model mine is, but those are the models listed on the manual. I opened the washer and the whole upper part of the wash tower was laying on the dishes! I took everything out, and began trying to think logically, and re-assemble the thing; nothing appears to be broken. page 17 of the manual is the only place that even shows this set up, but it's just a part description. As I am looking at the picture, I realize that the spray tow


... Whirlpool 24 in. DU920PW Built-In Dishwasher

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

Asko d3100 I have an asko d3100 dishwasher. Its just out of warranty and now the cup saucer light flashes and the water pump is continuing to pump even though there is no water. The dish washer wont start. What is the problem. I think the flashing cup saucer light is reporting a fault. If I know what the fault is for example faulty relay or pump then I can replace it. Can you help me with this one? Is there a service manual I prbably can get my hands on.


Remove the lower panel at the back of the machine. If there is water on the bottom pan, wipe it up with a towel or so, and the machine schould be like new again ;-)\015\012\015\012Good luck ... Dishwashers

Whirlpool DU927QWDG1 Hi, The problem I'm having with my dishwasher pertains to the door cover for the area I place the soap. There is a small spring which helps the door pop open to release the soap when washing. I cant figure out how to place the spring so that the pops open.....right now when I run the unit the door stays latched and the soap doesn't get dispensed. Any ideas on how to repair this or where I could maybe get a parts manual??? Your expertise will be greatly appreciated!!!!


... Whirlpool GU2400XTP Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Need the wiring diagram for the front panel/door of the dishwasher. The wiring diagram in the owners manual does not provide adequate description of which wires connect where. My problem is that, in taking off the door, two wires became disconnected and I cannot tell where they should be reconnected. I called Viking and they are unwilling to provide this (they prefer I call an authorized repair person). Does anyone know whether a repair manual exists for this and where I might get ahold of one.


This is all I could find go to this address www.specsserver.com/CACHE/FILE5412.PDF at the very end is wiring diagram but its not in detail ... Viking DFUD042 Built-in Dishwasher

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1472 seconds