Having problems with your Zanussi Dishwashers ?

Wiring on zanussi dw24 power switch

\015 I have to replace the power swich on a Zanussi dishwasher. I made a note of the connections, then threw it away! Now I don't know which colour cable goes where. Can anyone help. Regards Ed\015

Answers :

Repair Help & Product Troubleshooting for Zanussi Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wiring on zanussi dw24 power switch


... Zanussi Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

Bosch #SHE44C dishwasher does not fill. No power to the water solenoid, but power coming out of the control board and the emergency shut off float and switch is working. I need a manual with a wiring schematic and cycle sequence so I don't have to tear it completely apart to trace every wire. Thanks


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I purchased a diswasher (Hotpoint)about 1-1.5 years ago. It's model # is HDA3400G02CC and its SS# is TH887451Y. I don't think I registered it. No Matter, Two days ago, my garbage disposal stopped working. I checked the outlet. It had power. The switch to the Disposal was next to the outlet. I assumed that the switch was wired from the outlet. It wasn't. Bottom line, the switch nut was loose. I tightened it and problem solved. When I turned on the dishwasher, nothing happened. It acts like


I purchased your service (telephone support) and the dishwasher expert contacted me. We discussed the issue, he made recommendations. I followed his advise and solved the problem. Before I could recontact him, he called to follow up on my progress. ... GE Dishwashers

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

My wife and I just moved into our house and cannot get anything on the dishwasher to activate. We have checked fuses, lightswitches that might be wired to DW power -- nothing has worked. Is there a universal power switch I am missing?


Sounds like a power supply issue. Take off the lower panels below the door and look to the right side of the opening, you will see a little square steel cover. This cover is where your power comes into the dishwasher. Follow the line coming into the ... Whirlpool DU930PWS Built-in Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Have a jackson 300h that keeps burnning the power switch,can you help wow the wires are install,the colors are: blk ,white,violet,and wht/green wire,thank you


... Jackson 24 in. JPX-300H Built-in Dishwasher

I got this dishwasher from a friend that had mice chew the hoses and i was told that it worked perfect before the mice chewed it. I replaced the drain and fill hoses plus the power cord. when i put everything back together and power on I get F1 on the top drawer and the rotor rotates and the heater plate turns on. The botton drawer does nothing with no display. I checked all the wires with a meter and found good continuity thru every pin. I replaced the main filter board. I even switched the


Did the F1 error in the top drawer disappear after you replaced the mains filter board? ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Indesit d41 dishwasher overfilling, pressure switch seems ok(checked with multimeter) ,when pressure switch is manually operated the electro fill valve remains open. only time fill vave shuts is when power is off or door is open. can someone please help as i cant find wiring diagram or service guide online


Possible faulty pressure switch or a faulty drain pump ... Indesit 18 in. D41 Slim-Line Free-standing Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

Zanussi zsf4123 slimline dishwasher switch on, power light comes on, noyhing happems when program is selected. Is it likely it is the control unit? if so where can I get one in the UK


... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Jdb2100aws dishwasher - door handle fasteners loose, handle ready to drop off. This is a dissambly question: The middle section of the door has an upper one-third (which contains the input switch strip) and a lower two-thirds; the upper section must be removed to tighten the door handle fasteners. After wiring is disconnected (yes, power is OFF), the upper section appears to be held to the shell by some kind of barbed fastened from the inside, run through a tab on the door shell and into a fema


After removing the stainless cover l tried to disassemble the door further but found it difficult, there is a hard thick plastic cover, i took my dremel and cut a small hole large enough for a wrench to fit and tighten the thin nut on the handle, lin ... Jenn-Air 24 in. JDB2100AWS Built-in Dishwasher

Zanussi zsf6126 dishwasher showing fault 3, water inlet not opening, not receiving power to valve. tracing circuit without diagram have tested both level switches and valve but no fault found there. can you help please?


... Zanussi Dishwashers

We have a service contract with Broward Factory Service. My GE dishwaher went out with eater in it, no power. Checked the panel box flipped switch, nothing. The service tech. said the rinse aid cup leaked and ate thru the wiring, and he had read a recall about this. I am checking to see if Model #GSD3610Z00AA, Serial #ZS782757B is on the recall list.


I was trying to find out if the dishwasher was on a recall list, and I did by calling GE direct. It was not, so the service I have is replacing the rinse aid box.\015\012Thank you, ... GE Dishwashers

Model mdb7601awb diswasher . Nothing works , no buttons torn on or work when pushed, no action. 1.Have checked power to unit and is ok 2.checked door switches (2) and both work properly. 3. no visual discoloration on circuit board. There is a blue dot on the wiring harness from control board to button panel.When evaluating with magnifing glass I believe this to be blue ink droplet and not any burnning of harness. Need a Guru.


I have had the board replaced 5 times and the entire dishwasher replaced once. It was necessary to go to the state attorney general to get Maytag to extend the warranty. Just called the service center for the sixth time, after this the warranty will ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

Bosch SHU6802 dishwasher quit part way through wash. No lights showing and no response to off/on switch. Power is on at dishwasher input. Where can I find a wiring diagram?


Go to searsdirect. enter your model number and you can access a complete parts diagram and wiring diagram. http://www.searsp ... Bosch 23 in. SHU 8805 Built-in Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

I,ve got a prima LPR450 and it won't switch on, i've checked the obvious things like the fuse, circuit breaker and wires in the plug and they ere all fine. when i push the power button there is a faint clicking sound from inside the door.


... Dishwashers

HONDA power washer ON-OFF switch


More than likely the switch complete the circuit and allows the engine to run you canjumper the switch and see if it runs, if so, you can buy a switch from auto parts store and mount it ... Honda Pressure Washer PSI 3000

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0539 seconds