Having problems with your Dishwashers ?

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?

Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?

... Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.

Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e

The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo

So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Clean light is blinking, when you shut door and push start cycle nothing happens

Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!

... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.

... Whirlpool GU2400XTP Built-in Dishwasher

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c

Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y

... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?

... Frigidaire Dishwashers

Won't start. Seemed to be working fine a day ago. Then in mid cycle I opened the door because I was on the phone and it was too noisy (normal noise). Now , I shut the door and press start and nothing happens. No lights on the instrument panel. Nothing. Thanks.

You may have simply tripped a breaker, but if not it may be this.This may be a faulty door switch. If you look into the door locking mechanism carefully, you can see a small plastic bulb located either to the right or left of the locking Jaw. S ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Bosch SHE43F02UC/50 Lights on, but won't start any cycle....Regular Wash light only one on with timer showing 188.....pushing other buttons does nothing.....no noise, no water fill, just those two light remain on and nothing happens?

... Bosch Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.

... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!

... Maytag Dishwashers

Dishwasher won't start. I add dishwashing liquid, close the door, touch normal wash, it blinks CL CL Cl CL CL with the sensing and washing lights lit and when I push START, all lights go out and nothing happens.

... Dishwashers

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!

Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor

The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a

Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat

... Asko Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but

... GE 24 in. Profile PDW7300G Built-in Dishwasher

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.

I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You

... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

I have maytag dishwasher MDB7749Aww1 and when I close door. Then select cyle and push start,nothing happens.

... Maytag Dishwashers

I have a Whirlpool model DU1055KJVQ1, Type 575-0 under-counter dishwasher which is less than 2 years old. In the last couple of weeks, it wouldn't start intermittently, and I would need to hit cancel on the keypad, and then restart. Now that doesn't work. When I try and start the dishwasher, it doesn't work. I press Normal for the cycle, heated dry for the Option, and then hit Start. The buttons light up for 20 seconds or so, nothing happens and then they go out. Any ideas?

... Whirlpool Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.

Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1862 seconds