Having problems with your Dishwashers ?

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Answers :

Hi,
\015\012I think both the heater and thermostat / trip switches need to be checked.
\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.
\015\012Heating elements do fail after a few years.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Electrolux built in ESL4115 Dishwaser:- Starts the programe briefly but stops with two intermittent audible signals when you open the door the cycle has not really started and there is water at the bottom of the dishwasher(when u refer to manual says the sink spigot is blocked or water drain hose has not been correctly laid or is bent). I have had this for just over 1 year working ok up to this point, tried to see if there is a blockage, taken pipes out doesn't appear to be any blockage also th


... Electrolux Dishwashers

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye


Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

On my GE Profile Dishwasher model GSD4320Y72BB, water is leaking during the rinse cycle for a about 10-15 seconds from the bottom of the drain solenoid (GE part WD21X802). The water does not seen appear to be coming from another source. Are drain solenoids known to leak water? Thanks, Bud


They can leak if there is a bad seal or they do not have a tight connection. ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers

My Bosch Classixx (about 10 years old) dishwasher won't fill The problem has only started since I pulled it out and cleaned! The programme sounds are as normal but no water enters the machine. I detected a small leak on the inlet pipe and tightened that. The machine drains when I add water manually though it has made a lot of gurgling noises for some time now when draining. When tipped on its side water comes out of the bottom of the machine (not entirely clear but not dirty either). When upri


... Bosch SHU9915UC Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Hotpoint FDW80 Dishwasher. The drain pump runs continuously, even though there is no water inside, I poured water in with a kettle and it does drain correctly. After a short while fault code AL01 appears. I have removed the base tray to check the "anti-flood" swithch and that is OK, even with the switch disconnected, I still get AL01. Any ideas?


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a hotpoint hydrocare de luxe 7843 model it isnt plugged into the mains or any water flowing through it but when i was filling up the salt container some water split out and drained away and then leaked from the bottom just by the connection for the waste pipe


... Dishwashers

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My Maytag dishwasher does not drain. There is standing water in the bottom of the washer at the end of the cycle. I have checked the drain pipes for blockage and they appear to be clear. Please help.


... Maytag 24 in. MDBH750AWS Stainless Steel Free-Standing Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

I have a Zanussi dishwasher model DA 6141. For some time now it has not been completely discharging the water at the end of a cycle. But sometime it does completely dicharge.Two days ago it started leaking water from its bottom at the end of a cycle.I tried to locate the leak but was unsucessfuly. All the external plumbing is ok andf there is no leak from the discharge pipe nor water intake pipe. So perhaps its something to do with the water pump?


Hello David,\015\012\015\012Have you removed and cleaned both filters and checked they are inserted correctly? I've uploaded the filter cleaning instructions to Flickr for you:\015\012\015\012 ... Zanussi Dishwashers

I have a Frigidaire Dishwasher (PLDB998AC1). The wash selector panel will light up correctly, but when you press start it doesn't turn on and within about 5 seconds the lights on the selector panel go out. In addition there is some water in the bottom that doesn't appear to be draining. Do you have any suggestions?


... Frigidaire PLDB998A Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

I have a danby ddw496w that leaks water from the bottom of the machine when it goes into the drain cycle.it will start coming out the bottom as well as the drain outlet .Could it be a simple hose connection or is there something else that could cause this effect.the rear hoses are tight and it runs fine and does not leak untill it drains


Ditto- same issue, hoses are tight, just leaks through the bottom while draining. Anyone with advice? I just bought mine used, and the previous owner is willing to buy a replacement part, we just have to figure out what we need... ... Danby DDW496W Free-Standing Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2137 seconds