Having problems with your Dishwashers ?

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d

Answers :

The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you.
HI. this is a typical control fault that has rendered your unit inoperable. this damaged control boar should be replaced asap, if possible. I will post a link to the actual part below this text. You may purchase it form this link as well if you wish.


Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d

The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no

Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.

You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob

If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!

... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t

... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately

... Dishwashers

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile

Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour

Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no

... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE

... Haier ESD210 / ESD211 Built-in Dishwasher

I have a Maytag dishwasher model MDBTT60AWW. None of its wash modes will work when pressing their respective buttons. The Fields Service Test functioned normally with the exception of the "heated dry" and "sanitize" LEDs not being lit. Tried to perform the Manual Function Test, but none of the components would operate upon pressing the respective keys for testing their operation.

Hi, \015\012Sounds like either the control board or the keypad.Try removing power from the unit to see if it will reset.\015\012Now try running the diagnostics…RIBBON CABLE CLEANING ... Maytag 24 in. MDBH955AW Built-in Dishwasher

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.

Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"

... Kenmore Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.

... Kenmore 13743 Staimless Steel Built-in Dishwasher

Whirpool Dishwasher ADP5966 Turned dishwasher on. Only light that comes on is normal wash light. Start button is flashing when normal wash light is on. On pressing start button dishwasher does not work

Most likely the door switch is not making proper contact when you shut the door or the Start button is faulty. Needs someone to look in the door panel to fix. ... Whirlpool Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim

Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a kenmore dishwasher model 58715199400. the clean light keeps blinking. ive seen posts that say to press heated dry, normal wash buttons repeatedly until all lights flash. my model doesnt have a normal wash button, it has a rotating knob instead. any tips?

... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.

... Kenmore 16483 Built-in Dishwasher

When you push the eny wash cycle it will not light up. when you push the delay button it and the normal wash lights up. then if you push start it dose nothing (the heated button lights just a little)

... Jenn-Air JDB1105AWS Stainless Steel Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded

Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.

Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

Rinse only light is on and all of the wash rinse sanitize clean buttons come on and flash when you try to start it, if you change the setting to normal or heavy duty the wash light comes on then the rinse only light comes on and all above mentioned buttons flash until the tub is drained.

Hi\015\012 \015\012Try and reset the dishwasher by unplugging it for 5-10 minutes. Now check if you are still getting the same error you can try and press the following buttons to reset it-- \015\012Saini Rinse, He ... Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.

... GE GSD5320DBB Dishwasher

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button

That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1573 seconds