Having problems with your Dishwashers ?

Halfway though the cycle I get 4 beeps and flashes, I put the dishwasher in test and it found no faults when I tried the dishwasher again it works? fine a few times and the gets the same fault again.


Answers :

Hi and welcome to FixYa, I am Kelly.
\015\012Two things you should do:
\015\0121. Check the drain hose from the sump all the way to the sink or disposal connection.
\015\012 a. Remove the drain hose from EACH connection and check for obstructions.
\015\012 b. Dis-assemble the Air-Gap by lifting off the cover and unscrewing the cap nut. NOTE the installed position of the CAP as it will only install ONE WAY. Remove any debris in the Air-Gap passages.
\015\0122. Inspect the water level FLOAT or water level finger sensor (depending on your model of dishwasher) for either food particulate/blockage or restricted movement up and down of the water level float.
\015\012
\015\012By doing this you eliminate both drain and fill issues unless there is a problem with the inlet water flow supply. This should get rid of the intermittent mid-cycle 4 Beeps.
\015\012
\015\012If after doing the above, the problem persists; just respond here and we can continue troubleshooting.
\015\012
\015\012Thanks for choosing FixYa.
\015\012Kelly
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Halfway though the cycle I get 4 beeps and flashes, I put the dishwasher in test and it found no faults when I tried the dishwasher again it works? fine a few times and the gets the same fault again.


Hi and welcome to FixYa, I am Kelly. \015\012Two things you should do:\015\0121. Check the drain hose from the sump all the way to the sink or disposal connection. \015\012 a. Remove the drain hose from EACH conn ... Dishwashers

I have an Equator Mini Maid PLS602S dishwasher. It works fine, but the upper spray arm fell off and the clip and knob holding it in place are missing. Equator said they no longer make this model and don't have the parts. Can you tell me where to get the clip and knob to hold the upper spray arm in place. I know there is a little white clip - I actually had it but lost it, because when I tried to hold the arm in place with that, the next time I ran the dishwasher the arm fell off again. I


There are no parts sources that i can find for this dishwasher, but my suggestion to u is this, locate an appliance repair shop in the local area that has dishwasher parts, bring the portable unit down to the shop and see if they can mat ... Equator Dishwashers

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

My dishwasher is leaving a film on all the dishes some of the times. Other times the appliance works fine but more and more often it is leaving a white film on all the dishes as though the rinse cycle is not working well. I have tried filling the jet dry compartment and have been using the same jet dry and detergent as always. The dishwasher is about ten years old and has been working well up to a few weeks ago. Ideas?


Check inlet water quality & whether softening salt is required. Check and fill rinse aid. refer user manual. ... Maytag 24 in. MDB3700 Built-in Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Kenwood dishwasher KDW24FI/B has worked fine for approx 2 years. But now when I put my dishwasher on, the cycle never seems to end. After a few hours of running I opened the door to find the tablet hadn't dissolved but lots of steam coming out. I tried 2 more times and the same thing happened. The pump is working and everything seems ok. After reading the manual I have noticed the salt and rinse aid lights are iluminated. I have never put salt or rinse aid in since I had the dishwasher so thi


Lol is it a stereo or a kenmore, dishwashers dont use salt, but water softeners do ... Dishwashers

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Bosch dishwasher that was working just fine until I spilled a bag of uncooked pasta. I sent the pasta down the drain and ran the garbage disposal, subsequently clogging the pipes. I had to get a plumber to fix the drains, but he wouldn't unclog the dishwasher. I have tried myself to go under the sink and drain some hoses, but it didn't work. I also put some baking soda and vinegar into the drain, but no luck. What can I do?


It may simply be where the dishwasher drain attaches to your garbage disposal. There should be a hose clamp and can easily be taken off. If the clog's not right at the connection, chances are it's far. If there is an air gap, it will be within a f ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

We have started experiencing a problem with our Kenmore Elite 655.15982 dishwasher. Each time we close the door, NoHeatDry lid would go on immediately. It would stay as is of would go flashing. If you touch any button, LockOn lid would go on. Then no other buttons would respond. And often both NoHeatDry and LockOn indicators would be flashing... We tried turning machine for an extended time on the fuse, etc. At times it would work for some time and then cycle get stuck again at the same p


These errors are due to a faulty control board and needs to be replaced. If its still underranty get it fixed before it expires as it is a costly repair to replace. ... Dishwashers

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

Problem with my Kitchenaid KUDP02FR dishwasher. Working fine until yesterday, now the Cancel, Normal and Light/China indicator lights are all blinking at the same time. Cannot cancel out or restart the dishwasher. Tried unplugging to reset, but it just goes back to the lights flashing. Thanks!


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

I have a frigidaire FDB1050REC0 dishwasher that is working fine most of the time. Sometimes about 40 percent of the time, when we open the main door after it is finished with a normal cycle, we find a big clump of detergent left in the main detergent compartment and the detergent door is open. It is like the detergent is getting wet with the detergent door closed and then when it is supposed to open, the detergent is wet and clumps. We switched to liquid detergent and the same thing is happening


... Frigidaire Dishwashers

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Have no water getting to my dishwasher i have filled salt and rinse aid as the lights were on on the last time it worked tryed all the advice what can i try next


No water ! - check the flow first at your tap end or the at machine entry gland nut. Clean the filter by pulling it out. It will be small in size. If inlet valve not getting opened also will lead to this problem.For trying oth ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1850 seconds