Having problems with your Dishwashers ?

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


Answers :

I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufacturer should have done in the factory and not made 1\015\012dollar off of this defective D/W until it proved this to be ready .What\015\012has happened to Quality Control ? Does it no longer matter ? Very sorry\015\012,you should seek a refund ASAP.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any error codes, New World sent a replacement PCB which made no difference except now have no error code. Circ pump, inlet valve, heater, drain pump checked independantly all worked.


I f you have warranty on this please call them, you have a defective\015\012D/W.Unless there is no charge for repairs ,don't spend a dollar on what\015\012is going to be a on going problem ahead.To explain how to fix this is\015\012what the manufactu ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

E1 Error code - no leaks - new pump - new pc board in Dec. 09


\015\012The most common reason for an E1 error on an LD dishwasher (that does not have a leak, including directly under the dishwasher) is the drain hose between the dishwasher and the drain does not have a rise in it between the DW and the dra ... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

DISHWASHER-GE GL613716A will not drain. re/re drain and removed restriction,food ect. it will not drain still. performed self diagnosis on front control panel as per trouble shooting information supplied with dishwasher when i bought it, all tests passed except when commanded on, the pump did not drain water from the dishwasher, i do not know if the pump came on as all test functions are perfomed at the same time for some reason, which made a bit of noise making it hard to even hear the pump. th


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Dishwashers

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I ran a load of laundry in whirlpoo[ duet ht, model ghw9400pl4, error code p-09 was indicated. water was overflowing from door, and water was continuing to fill the tub. I turned off the faucets, unplugged & restarted in drain mode it hummed but would not drain. I turned the faucets back on and retried to drain but it would only hum. I manually removed the water by losening pump filter. There was no debree in filter except for a little bit of hair. The pump & vain was free & clean, and I co


It is your mixer value that is malfunctioning. ... Whirlpool Dishwashers

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a McCulloch model number FHH18A/FHH20C. The brass fitting that comes out of the pump has broken. It's brass and plastic. McCulloch claims there is no replacement part, except to purchase a new pump and motor. Is there any after-market check valves that would replace this fitting/valve?


... Pressure Washers

Bosch Dishwasher has error code e24, I checked the line, replaced with new pump, new control unit and call repair man no luck. It works on and off. I get it run then next cyle nothing. Heelp!


... Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

Hi I have a kleenmaid dw3 dishwasher that will not wash it will go through to the wash cycle in economy [no prewash] and then it just stops. in day the dishwasher just started, weeks later. I hadn't realized it was still on as we usuallydon't turn the power button off. i'v put in a new timer but that made no difference. Can you help me, please! Sonya


Hi and welcome to FixYa,Offhand, I am tempted to think that there is no major component that would require replacement. At most would be the door close sensor/switch. May I suggest a simple test, jump the two wires leading to the switch a ... Dishwashers

My dishwasher will not drain. it goes through the first 10 minutes of a program then i get the OE error code. i have checked my hose for kink or clogged-there is none, i have made sure it was level. i would like to get the filter off but it looks like i would have to take the drain pump out from the bottom to check if any thing is plugging it. was just wondering if anyone has any tips that would help. thanx


1)check the drain pump working\015\0122)check any block from drain pump to drain hose. ... LG LDF6810 Built-in Dishwasher

New World Integrated Dishwasher DW60 E4 flashing and beeping. Managed to get it going for a while with a d/w cleaner, it filled, water heated but then E4 error kept flashing and it stopped, had to scoop water out. Cannot find instruction booklet to check fault. Please advise. Many thanks.


... Dishwashers

Asko 1755 dishwasher. The pump keeps running We need to replace a new PCB P/N: DW955 8057931-05 Is it available?


My Asko Model 1585, Type DW 95.4 Circulation pump just died. I have the following parts available (All in working condition):* 8057931-05 Control Board (this is the replacement part AFTER the recall)* 8057083 Drain Pump* 8057085 Fan ci ... Dishwashers

I have a new world DW60 dishwasher which comes up with an E1 error code. I can't find what it means anywhere & I have checked the manual. Can it be repaired? Do you do the parts needed? I appreciate your help. Michelle


... Dishwashers

I am constantly getting a E2 error on my New world Dishwasher with some of the washes not completing in the cycle what is causing this


Hi there,\012Well It is a blockage in the water outlet system (located at the bottom of appliance) and is generally caused by excessive food being left on the plate and getting into this pipe and causing a blockage. This in turn builds up ... Dishwashers

My dishlex globale 300 has a modle no that is dx300wa*02 the eco light and pump keeps running i have recieved advice to drain/dryout the kidney shapped over flow tray but mine doesn't seem to have one. i've taken off the bottom cover to get a closer look but still can't see it i've also tried tipping the washer on it's left side right side,backside and even upside down to try and drain the extra water but that has made no difference please help


Hi,\015\012Try taking the dishwasher out of its wall space and tipping it back and forth. Apparently the weight of water gathering in some component triggers the 'eco' function. Allow it to evaporate by waiting for few days. ... Dishwashers

LEAK IN THE CIRCULATING PUMP. SEEMS TO BE COMING FROM THE O-RINGS ON THE SHAFT. I HAVE CHANGED LARGE O-RINGS, DOESNT SEEM TO HAVE MADE MUCH DIFFERENCE


... Frigidaire 24 in. GLD2250RD Built-in Dishwasher

Cloudy glasses I have a Kenmore Classic dishwasher probably from the early 80's. It works fine except recently my glassware(new glasses) has started coming out cloudy(looking like there are soap spots on it) I have made sure I have the Jet Dry in there and I have even re-rinsed but they still look like that. Any suggestions as to why this is happening? Thank you Rita


Dishwashing detergent will etch fine glassware. Don't wash them in the dishwasher. ... Dishwashers

I've had 2 repairmen out for my whirlpool dishwasher (2 yrs old) which is leaving a removeable film on the dishes. White powder, looks like soap. One put in a new soap dispenser (made no difference) the other said it was a hard water problem. Can hard water cause a powder/soap film?


The problem is hard water. www.dishwasherfilter.com has a product that solves this once and for all. very affordable and guaranteed to work. you will love the results. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

Error code e6 on new world dw60 dishwasher? - Dishwashers


... Dishwashers

Model SHU33AO2UC /40 The top rack leaves lots of residue and stuff on glasses. We had a repairman out, he cleaned out the pump intake, and we are careful to clean everything before putting it in the dishwasher. I have made sure all holes in the spinners are clean and don't crowd the glasses. We have also tried different detergents. The dishwasher is 4 yrs old and is used daily. We also use jet dry.


... Bosch Dishwashers

Air pump for door seal not activated MODEL-DD601V2 . Dual draw dish washer.Would it be the PCB is faulty or a program error?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1196 seconds