Having problems with your Dishwashers ?

Is there a reset button for a hard water softener


Answers :

Http://www.jordansmanuals.com/ServiceManuals/FP/Dishwasher/DD605/DD605%20Parts%20Manual.pdf
\012
\012It can be manualy programed with your machine this manual will guide you
\012
\012Good Luck
No. But if you are experiencing hard water problems or ran out of salt and have added salt now you need to push the regen button to manually regenerate the softener. This needs to be done 3 days in a row to regain soft water.
RJH2O
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is there a reset button for a hard water softener


Http://www.jordansmanuals.com/ServiceManuals/FP/Dishwasher/DD605/DD605%20Parts%20Manual.pdf\012\012It ca ... Dishwashers

I need to know how to reset the "brain" the start button is flashing and won't stop when I close the door it makes a humming noise and no water is running. I turned off the breaker but it won't reset. Is there like a "hard reset" I can do


I don't think you may need to reset the dishwasher. All that might be happening is the float switch located in the base may be malfunctioning. It could be stuck. Try pushing it down and see if it lifts up by itself. It should only lift when water is ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks


... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Water doesn't seem to be getting in with the cycle except at a minimum level...have retried 4 cycles worth and done reset button imbetween. everything is baked on soap still hard hear regular sounds during cycle


Check to make sure water solinoid valve is getting voltage for a long enough time. if the water pressure out of control valve is weak it is definately the water valve. most of times limited water is the valve is clogged with calcium. ... Asko Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

My bosch dishwasher, one month old, has the active light flashing and the reset button won't reset it when I push it. A friend that was over opened the door when it was running because she can with hers, but ever since then, I had to take the water out and the active light is flashing and the wash light is lite. I hold the reset button for 5 seconds and then I shut it off for about 5 minutes, but when I turn it back on, the same things are happening


It sounds like the float is stuck. There is a float that stops the water from coming out when you open the door. It sounds like your friend stoped it in mid cycle and it jammed in the open position. Look on the inside of the machine for a plastic pie ... Bosch Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

MY GE WATER SOFTENER QUIT WORKING PROPERLY AFTER 6 MONTHS ,I HAVE HAD SERVICE CALLS AT $150 EACH TO NO AVAIL IT DRAWS SALT BRINE MY WATER HARDNESS IS 17 I HAVE SOFTENER SET TO 22 .I HAVE PRE WATER FILTERS HAVE TRIED DIFFERENT SALTS ALL TO NO AVAIL, NEITHER GE OR HOME DEPOT WANT TO HELP AS NOW I AM OUT OF WARRANTY I HAVE BEEN ILL AND IN THE HOSPITAL (CANCER) THAT'S WHY I HAVE GONE OUT OF THE WARRANTY TIME MODEL GXSF30H PURCHASED 19/02/10


As you have purchased GE water softener and stop working after 6 months,then you need to check it from an expert technician and if he is able to solve this issue,then it good and well, but if this takes more money to repair and not under warranty the ... GE 30000 Grain Water Softener GXSF30H

Aeg bs45e water heater, heats water for 5 mins and then 'trip' light comes on and pressing reset button does nothing, heater must be turned off for 5 to 10 minutes b4 it will heat water again


... Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

I would like to know if there is a reset button on the water inlet valve and if so, where can I locate it? I have removed the lower front covers and see the valve, but cannot locate a reset button. GE500 Dishwasher


There is no reset button. If no water is coming in you probably have a bad waer valve. ... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Is there a reset button on dishwasher model S62NXPLP7653? It filled with water, then shut off and won't restart. If there is no reset button, what other thing should I try. The unit is fairly new, maybe 6 to 8 months old.


... Whirlpool Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

When starting my GE Dishwasher I made a mistake & pushed the start button twice, now the cycles are all out of sync, what should I do to start it? It will run but sounds like there is no water in it. I pushed the reset button,but turned it off, because I was afraid I would burn it up, with no water coming in.


Push and hold the reset button for about 15 seconds should be ok,if not do same with start botton.adrian,,,,, ... GE Dishwashers

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

Setting the water hardness system on Beko DWD 4310W. The handbook instructions seem to be wrong. There's no display panel on the machine as it states, and it tells you to press and hold Start/Stop button and switch the On/Off button, release the On/Off button, press and hold Start/Stop button for 10 seconds,( which you are still pressing anyway!) Then it says the last setting will be displayed on the panel for five seconds. But no panel.Totally confusing.


... Dishwashers

Brand new high end electrolux dishwasher perfomring horribly - likely due to hard water issue. Cloudy glass and resident left on dishes. Have the rinse agent set at max and hot water is at 150F...is the only solution a water softener??


Dishwashers have a water softener incorporated but this needs salt to regenerate. have you put salt in? ... Dishwashers

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1007 seconds