Having problems with your Pressure Washers ?

Where can I get a Karcher 550 MS Pressure Hose from

Answers :

Repair Help & Product Troubleshooting for Pressure Washers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Karcher 330 electric power washer. When connected and set to highest pressure (on variable wand) I get no motor action unless I reduce wand setting, then I get a little boost but not much. If I use high pressure conical wand I get high pressure sometimes, other times motor does not go and no pressure is delivered. I have replaced the high pressure hose.

Just wondering. have you tried it without an attachment to see what kind of pressure you get ... Karcher K2.26 Electric Power Washer

High pressure hose. How do you get if off the karcher k 3.99

Hi, you have a little black clip in the gun hand where the hose pushes in, just pull it out and the the hose will pullout. ... Karcher K 5.85 M Electric Pressure Washer

I cannot get my Karcher 2600 psi gas powered pressure washer to start. Got gas oil no pressure build up in hose.

... Karcher 2500 PSI Pressure Washer

Pressure hose not working on Karcher pressure washer

A common problem with these is a pressure valve inside the unit that controls the power to the pump. If the unit has not been used for some time the valve can stick.\015\012\015\012Does the motor run when you press the trigger? \015 ... Karcher Pressure Washers

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.

If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

Where can I get a Karcher 550 MS Pressure Hose from

... Pressure Washers

Cant change the high pressure hose on a Karcher

On the Kärcher, you have a bayonet mount at the base of the tip end of the pistol grip. This is where you attach different types of nozzles and gadgets after having removed the existing sprayer tube. Just push in and turn a quarter of a turn, th ... Karcher G 2600 VH Gas Pressure Washer

Pressure Once I have the powerwasher started and going (water to it before starting) i can't get it to go to full pressure it will prime up like it's going to go to full pressure give me just a shot of full pressure then go back down to probably half pressure and remain there then prime again for a second then back a coninues cycle! Maybe there's a seal or something somewhere I should look at. Hose and pressure from house is good, the seal whee the hose attaches to the bottom of the washer is ne

This is usually a problem with the "dump valve" defective in not being able to hold the pressure but only able to release it prematurely as it should only do so when to much pressur is built up inline. Only recommend qualified pump tech. But check pu ... Coleman Pressure Washers

Assembly plans for karcher 2400 psi pressure i recently had a problem, with my pressure washer. i was cleaning out my hose and took the hose assembly and brass fitting off. run water threw it thought i had cleand it out, put it back together and now when i hooked my water hose back up the water comes out of the despencer instead of the pressure wand. does eny one no what i need to do to revurse this?

... Honda Karcher G2400HH-R Pressure Washer

Hy; I have a karcher 580 I had to replace gun complete so I bough a simoniz xe01-001 at simoniz.osirus.ca/ for your info 69$ complete ***.I install NOW I get pulse up & down ONLY when trigger is press I turn valve down i only get 10% of pressure if i turn valve up that is when it start pulsing pressure up & down it wont keep pressure up ... Bob...

Most likely problem is that the tip is too small causing Unloader to bypass or restriction/debris in tip. Install clean tip of proper size or 1/2 size larger (example from 2.5 gpm to 3 gpm ) to prevent slow pulse. If tip is clean and /o ... Karcher 2500 PSI Pressure Washer

No pressure i have a karcher g 2600 vh i wasnt getting pressure and i found that my spill valve was faulty it was actually broken i bought a new one installed it and im still not getting much better pressure ive taken the pump apart and checked for build ups blew thru the valves wirh the compressor and there appear to be no blockages

... Karcher G 2600 VH Gas Pressure Washer

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.

... Karcher 2500 PSI Pressure Washer

DuraBuilt 1404. Motor kicks in for two seconds, then quits. High pressure hose blew off and I could barely get it threaded back on. Quick coupler broke so I hooked garden hose up direct. Is lack of quick coupler maybe the problem? Could I be missing a part on high pressure hose that makes it so difficult to thread onto male fitting? Thanks! Bob

... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer


... Pressure Washers

How to change a hose on a karcher 9040 pressure whasher

... Pressure Washers

Hi, I have a Karcher 3.75 jubilee powerwasher, there is water coming out from where the high pressure hose connects to the machine and the unit pulses when idling but works perfectly without drop in water pressure, when trigger on gun is pulled, on closer examination the metal connection on the hose turns, is this the problem or something else. thank you.

... Karcher Pressure Washers

I have had 3 Karcher pressure washers all experience the same problem and so have two of my neighbors. Our area has very hard water and it causes problems with the washer not bringing up the pressure when the trigger is pulled (or surges up and down) and the nozzles clogging, etc. The service repair facilities cannot tell me how to prevent this. Many attempts to contact Karcher for advice have been ignored. I have been thinking that perhaps running the engine for a few seconds with no hoses a

If your water is that hard (and it appears it is) WD40 will NOT solve the problem. You should look into a water softener. However, chances are that a small, inexpensive model will not have the flow capacity required for a pressure washer. You'll like ... Karcher K2.26 Electric Power Washer

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

My Karcher 4000 SHR Pressure Washer pressure pulses when operating. I have checked with Karcher Technical Support and all their trouble shooting procedures except checking the unloading valve. Where is this valve, how do I get to it and how do I lubricate it?

It sounds like your unloading valve is crudded up with mineral deposits and stuck in a partway open state. look for a plastic cover with a silver snap on top; pry off the silver snap and lift off the plastic cover; next remove the two screws on the ... Honda Karcher G4000RH Pressure Washer

Split Hose I have an Aussie Eco Clean H120 pressure cleaner and the pressure hose has split. can anyone tell me where I can get a replacement. Thank you.

I believe this link will take you to contact info for ordering parts directly.\015\012\015\012www.aussiepumps.com.au ... Pressure Washers

I have same problem with Chicago Electric # 47761 electric pressure washer as Aug 10 2010 writer had w/ Karcher 2500. Runs briefly then stops. Pressure is trapped in hose. I cleaned hose disassembled & greased valve in handle. No improvement. Problem appears to be premature wear of trigger cam in handle - both are plastic. Valve body is rigid nylon. Any thoughts??

... Pressure Washers

My karcher cleaner does not get the full pressure at nozzle

... Pressure Washers

My Karcher 411A seems to have lost pressure. Behaviour is this, when you press the water release on the spray gun you get 100% pressure for like 10 seconds and then it seems to dwindle down to 30-40% of its total pressure. When the pressure cuts down I can hear more noise coming from the gun sprayer aswell. So not sure if the problem is in the gun or the main pump unit ?

Sounds more like a clog on the intake side. Check the filter and the hose on that side. ... Pressure Washers

I have a 3000 psi karcher pressure washer with honda engine, the problem is for a while the pressure would kick in and out, now only water hose pressure, the water supply is fine, what is the problem

Sounds like you need a seal and bladder rebuild < if you liver in a cold environmet for winters please dont forget to winterize your washres every year before winter ... Karcher G3025OH Pressure Washer

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se

Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0713 seconds