Having problems with your Asko Dishwashers ?

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


Answers :

This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the timer may be at fault.\015\012Dishwasher timers can't be repaired. If yours is defective, replace it. Best bet is to call in a repair man to run a few tests and zccurately diagnose the cause.

However, considering that your machine is 8 years old and you've already got it repaired once, my honest advice would be to get yourself a new machine, preferably a Whirlpool or Kitchenaid dishwasher. A really, really good and quiet\015\012one will run you about $500. If you want the stainless steel interior\015\012(though, I don’t see the point of this for a residential dishwasher)\015\012it’ll run you a few hundred more.

Asko is not a very reliable machine. (Its a wonder yours lasted all of 8 years!) Their dishwashers are famous in the repairing community as electrical\015\012nightmares – their defining characteristic is spontaneous combustion....you pay twice as much for a dishwasher that breaks down twice as often,\015\012takes twice as long to get parts for, and costs twice as much to repair.

Hope that helps!
You can find it on the inter net for doing it your self
\015\012
\015\012please check this link for instructions
\015\012
\015\012www.applianceaid.com
Repair Help & Product Troubleshooting for Asko Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Hi, I have a KitchenAid Model: KUDP02FRSS1. I push start/resume (it blinks) and am given the normal cycle with heated dry, or rinse only as my options. No other buttons work. Also, soap tray does not open during cycle. I replaced circuit board #8559825 to no avail. Is problem likely the control panel?


Control panel is the most likely the cause of your problem. A faulty door switch may also cause this. ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

The dishwashwer didn'tallow me to select the various wash cycles. Only light wash worked. I replaced the main circuit board and now only the high temp wash/semi rinse/ heated dry option work.


... Electrolux Kenmore 24 in. Built-In Dishwasher with 5-level Precision Direct Water Delivery System Dishwasher

Rinse agent light stays on the machine keeps running countsdown to 1 doesnt get hot i replaced the circuit board


... Bosch SHI6805 Dishwasher

I have the quiest series 300 series and the main board has been replaced but the only thing that comes on is the rinse light.The circuits are fine as we had them checked/


The touch membranes are pretty common on this dishwasher, its part of the control panel console. ... Maytag MDB7100AWB Dishwasher

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

Model EB2404SS/WW, the soap dispenser does not open during the wash cycle, replaced the actuator, still does not work, which circuit board is at fault, can the switch for the dispensor be replaced on the circuit board?


... Samsung Dishwashers

My Hobart AM-14 is displaying a water temperature of 255 degrees but it is not heating the water. I believe the heating elements are good. I don't want to replace the circuit board if the problem


The thermistor in your float and probe assembly or it's associated wiring is shorted. ... Hobart 41 in. AM14-255 Free-standing Dishwasher

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

It doesn't work at all no lights anywhere. I ordered and replaced new switches, and replaced the control board. The circuit breaker is on, and if I put one of the little meters that just tells if you have either 120 or 220 volts accross the two white wired connections on the board, 110 lights up. The float seeks to move freely.


If you have no lights at all and you have power to the circuit double check that the circuit board is connected properly first since you replaced that. On some models there is a safety circuit installed that disconnects power in the event it detects ... Kenmore 24 in. 15932 Built-in Dishwasher

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Hey guys, I am a dishwasher repair guy in barbados, the caribbean. I am having problems with a Hobart LX30H. the relay board is doing half the things right and the othrs not at all. I replaced it with a new one and the same results. At startup, the wash sump heater and wash motor are running, but the fill valve, drain valve and rinse booster are not running. Hence the startup operation is stalled. the funny thing is that the rinse booster and fill valve led's on the relay board light up at


Not sure what sort of problems (fault codes etc) you were having before you chose to go on the path of replacing the relay board.\015\012\015\012It might help to know what fault codes you have been noticing.\015\012\015\012One ... Dishwashers

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Having trouble with dishwasher- I feel like dishes are not getting clean- will replacing circuit board on dishwasher help dishing become cleaner?


You may need to clean out the filters that keep food from being pumped up to spray out of the sprayers. This will depend on your make and model as to how to do this. Clogged filters will reduce the amount of water being sprayed. Try opening the do ... Maytag Dishwashers

My DD 603 has burnt out the power board marked 34740453-G. It tripped the circuit breaker at the power box. It is burnt out on the board where the loom connects for the upper washer. It is burnt vertually in the centre of where the loom joins to the power board and the centre of the loom. I am wondering if something else has gone wrong with the washer causing the power board to burn out, or can i just replace the power board?


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Maytag Dishwasher Model # MDB7609AWW1 replaced thermal fuse and circuit board still does not work


... Maytag Dishwashers

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

I have a kenmore quiet guard 3 dishwasher 665.743833 it does not turn on when i select any cycle non of the lights tuen on i replaced the circuit board and the thermal fuse still nothing what


... Dishwashers

I have a Bosch Dishwasher SHU5302. A year ago it just kept on running. I ran a diagnostic test and replaced the circuit board that had a burn spot. The unit washed after that but would not drain wa


... Dishwashers

Dishwasher still not working after replacing circuit board ASM


... GE 24 in. GSD6660GSS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1008 seconds