Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Answers :

Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Hi, I have a Miele G681 dish washer with an intake/drain light problem. I've read all posts about similar problems I could find both on this forum and others but I'm afraid I still can't figure my problem out. The intake/drain light starts blinking mid way into the dishwashing process. The dish washer fills up, rinses, drains, water is hot, everything seems to function just fine. Some time after the tablet drops from its door mounted container, and the time estimate reaches 46 minutes r


... Dishwashers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

I have a kohler command pro 8.5 on a porter cable pressure washer. Yesterday it started just fine. Today I pulled the start rope and there was no resistance and the engine did not turn over. The pull rope rewound just fine and I tried again with the same result. After several tries it caught just a little near the end of the pull and the engine started. What is the cause of this problem?


... Porter Cable Pressure Washers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

I have a G2500VH pressure washer that has started to pulse when the trigger is squeezed. This happens if I use the 0,25, and 40 degree nozzles BUT if I use the one for low pressure(detergent use) it will hold pressure fine. I have changed the unloader valve, checked all the valves and seals ad they seem to be fine. What could be the problem?


Do you mean pressure on and off with the hp tips and smooth and steady with chemical tip? ... Pressure Washers

I have a reconditioned Husky 3000PSI with Honda GCV190. We used it for a couple of hours. Had to put gas in it once and it started up no problem. However when we undid the water hose and moved it to back yard we could not get it to start again. Ckd oil dip stick and was fine. Any thoughts?


... Pressure Washers

Just bought a john deere 3300 power washer. It started with no problem. shut it off to answer the phone. When I went to start it the pull cord wouln't pull tryed everything but still the pull cord was in a locked position. Don't know what to do hoping you have an answer for me


First turn off the water to the machine. pull the trigger to release any trapped pressure in the high pressure hose, then try to start the machine. if it starts then turn on the water to the machine.it may be that the engine is tryi ... Pressure Washers

Have a 2400 karcher press. washer engine starts runs fine for 15 sec . then quits .I walk away and come back in 10 minutes does same thing. Checked tank and it is not plugged. Appears to have vacuum fuel pump. could that be problem?


It sounds like the fuel bowl is not filling quickly enough. Turn the fuel tap off. Then take the fuel bowl off the carby. You will see a plastic float. Above the float is a needle (small pin like) that should shut the fuel off & let it run also. Turn ... Karcher G3025OH Pressure Washer

I have an Excell VR2500 pressure washer with B & S 6.5 HP engine. It was running fine, but then stalled out and now will not start. Has clean gas and full oil. I pulled the spark plug it is producing a sufficient spark when starter cord is pulled. Any ideas what might be causing the problem? Please help.


The key things to check are the spark plug, the air filter, the fuel. If those are all new and in good shape then you probably have gum in the carburator. Get a can of starter fluid and a helper. One person squirt the starter fluid into the air in ... Briggs & Stratton Pressure Washers

Electrical expert Replaced our dish detergent dispenser cup. Everything was fine with that. However, the display only lights up for two cycles and the start button is not functioning. We have re-done the two wiring harness pieces and shut the power off via circuit a couple of times now, but the problem remains. Any suggestions?


... GE 24 in. Profile PDW7800 Built-in Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

I have a Karcher K3.91M pressure washer that pulsates when the trigger is released (off). It works fine when turned on, pressure seems OK. Before this started the unit would just turn off until I again wanted to use it. Is it a problem ? Correctable? All connections seem tight & I see no leakage.


... Karcher K 5.85 M Electric Pressure Washer

Frigidaire dishwasher Model GLD2250RD50: Stopped washing dishes when a ran the garburator full of water, panel lights of high temp and nearby started flashing, then I pressed cancel/start, lights went out the washer wont run, checked breaker no problem. door latched,


... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Fagor lf-017s Hi, my fagor dish washer is showing an f3 alarm. f3 shows as a flood or not draining alarm in my booklet. However there is no remaining water inside the dishwasher. I have removed the dishwasher and checked the pump which is fine. The pump is running at the start of each cycle until thr f3 alarm steps in. Any ideas why the machine is still asking to drain when there is no water inside?


The water level float is stuck in the "UP" position ... Fagor Dishwashers

Hi. I have own a Karcher K 2.35 power washer. It has developed a problem where it's fine for the first 10 minutes of operation. Then it cuts out and won't start again for halfan hour. Any idears please


Sounds like the thermal protection is tripping. If the motor has a problem or is running with to high of Amps it will heat up and cause this problem. ... Karcher K2.26 Electric Power Washer

Quits Running Pressure washer will run for 15 or 20 min. then quits running. If I let it sit for 10 min. it will start and run fine for another 15 or 20 min and quit running again. Whats causing this problem?


... Honda Pressure Washer PSI 3000

All lights are flashing but he dish washer wont start.. was working fine before I went out of town this last weekend..


It might be that you had a power surge try unplugging the unit for a few minutes or trip the breaker.\015\012 good luck,\015\012 rsmith972278 ... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

My pressure washer starts fine but after you run


HAVE GX390 RUNS ON LOW IDEL THAN DIES ON HIGH NEW GAS ... Honda Pressure Washer PSI 3000

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

Unable to start gas engine on a NorthStar pressure washer


Disassemble and clean the carb. If it ran briefly with the starer fluid then gasoline is not coming through the carb. ... Northstar Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1471 seconds