Having problems with your Bosch Dishwashers ?

BOSCH DISHWASHER SG157MO5GB REFITTED AFTER NEW KITCHEN INSTALLED. FOUND PLASTIC PART (LIKE SMALL SHOWER HEAD) ROLLING AROUND INSIDE. WHERE SHOULD IT BE FIXED, PLEASE ?


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

BOSCH DISHWASHER SG157MO5GB REFITTED AFTER NEW KITCHEN INSTALLED. FOUND PLASTIC PART (LIKE SMALL SHOWER HEAD) ROLLING AROUND INSIDE. WHERE SHOULD IT BE FIXED, PLEASE ?


... Bosch Dishwashers

Hi, We have a small CDI454-80 Candy Dishwasher. It is just 18 months old and has only been used around twenty to thirty times. It has recently started to leave a film on all the dishes after the wash is complete. We noticed it a few days ago and have tried different tablets but with no better results. We have also noticed that the cutlery is getting brown rust like marks on everything in the silver tray. PLEASE HELP! Thanks, Dave


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Candy A8001 Dishwasher

I have model EIDW6305GS0. It is a little over a year old. There are small puddles of water under the door after running it but not every time. When I run my hand along the bottom edge I can feel a wet sponge like material between the outside and inside of the door. I assume a gasket or insultation material are leaking. Is this something I can fix myself. Thanks, Mary Herman [email protected]


... Electrolux Dishwashers

Door leak I have a small leak between the bottom of the dishwasher door the lower service panel on the dishwashere. I did replace the seal on the inside bottom of the door along with the other parts that come with the door seal. Could there be a gasket leak around the detergent dispenser or the vent at the top of the inside of the door. I did not check the water lever as was mentioned in a previous question on water level, but the float does move up and down quite freely. Any suggestions as to w


I had my dishwasher leaking alot at the bottom of the doo,r and found out that the steam vent was very cloged with gunk. After taking the vent cover off on the inside of the door and cleaning, then putting the vent cover back on NO MORE leaking. Th ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Low flow Please advise how to disassemble Delta shower head A112.18.1 I have the handle portion apart but can't find the key to removing the head portion. Your help would be appreciated. Gene


... Dishwashers

Please help my wirlpool ikea diswasher was working well but suddenly it stopped!I have one of those DWF small ones and have the buttons on the inside top part of the door. when I press the start button nothing happens and when I close the door the alarm sound goes off!! can anyone help me please


Try dropping power to the unit for a minute and see if it will reset itself. if not, you have a logic board failure. that or a door switch. check the manual for an indication on the warning alarm.good luckmark ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Tappan Dish washer, model TDB21ORFS5. There is a strainer in the bottom and I would like to clean it. We are getting some very small particules of food left on our top rack inside of large cups and glasses. The strainer has a "peg" and it can be turned, but I wanted not to breck anything. The inside of the door it says it was built by electrolux.


Refer user guide. They would have given clear instructions regarding cleaning.If you are finding it difficult pour sufficient water in the wash chamber. When the particles float remove them manually using a small cup. It's lit ... Dishwashers

I have a DU1055xtss3 dishwasher. It is about two years old. It does fine cleaning the dishes but about a week ago it started making really loud noises. It sounds like it is straining. This dishwasher was never very quiet but it is super loud now. We looked around inside and used a flashlight to see deep inside, everything looks good. Do you have a suggestion. Should I have a plumber check it out?


First find out where the loud noise came from,then check the water supply then check the drying fan maybe some screws are losing ... Whirlpool DU1055XTS Built-in Dishwasher

Dishwasher Grit? Hi, I have a dishwasher BOSCH around 4 years old. It has been fine but has for past couple months been leaving a sand-like grit inside glasses and on plates. This is nothing that I can pinpoint as having come from the dirty dishes - food on anything placed in to be washed, its driving me nuts! Can you help?? Julie, Sydney Australia


Hi julie\015\012\015\012\015\012 Chances are you are using to much detergent and the water is not hot enough. cut back on the detergent and run your hot water tap at the sink first and that should fix it.\015\012\015\01 ... Dishwashers

I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?


... Dishwashers

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a GE roll around dishwasher, Model GSC3200Z03BL. It worked one night, did not work the next. After hooking intake/discharge hose to faucet and turning to start, no water is pumped in. Only a humming noise much like something is stuck preventing pump from allowing water in. What to do? Appreciate the assist.


First off.. the pump does not let water in.. it takes water from your sink faucette via the hose and allows it to enter the DW via an inlet electrically operated valve. If that valve is not commanded by the control system to open, then no water will ... GE Dishwashers

Portable Dishwasher I have a older model portable dishwasher. It works great and until it goes out I would like to keep it. I am wondering how or what I will need to make the dishwasher a non-portable. I get so tired of moving it across the kitchen floor. Is there anyway I can hook something up to my lines underneath the sink so it will stay where it is? it is only about 10 ft away from my sink but that it alot of moving around when it is full of dishes. Please help. [email protected]


I sent you and email with some instructions, Look to hear from you soon!! ... Kenmore 17252 Free-standing Dishwasher

Dishwasher is making a loud whistling sound when washing dish on normal cycle. Without dish on eco cycle it still is loud, like the water really bangs around inside


... Frigidaire Dishwashers

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

The wash pump is leaking, not at the larger joining o-ring seal, but through the vents in the bottom of the motor just past the blade/rotor. Is there a small o-ring inside that is on the shaft that may be leaking? Is there a schematic breakdown of this motor somewhere? I already ordered a new one, and will "play" with the old one to see if I can fix it, just looking for some direction.


The shaft seal has failed. Often the top ball bearing becomes noisy after having the water leak through it. The seal is probably a lip seal rather than an O ring. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Cloudy Dishes My dishes have just recently started turning cloudy with white fllm. This has never happened before and the dishwasher is approximately two years old. There is no issues with hard water, and have used Jet Dry, have tried cleaning it with bleach and vinegar, and have used soap and no soap. Please give me suggestions as to why this would start occurring now. I took off the inside panel and it was full of all kinds of gunk which I since cleaned out. I would like to know how to avoid t


There is a new product out that filters the water going into your dishwasher. the film or cloudy white look is caused by hard water. this filter eliminates the problem and is very affordable. you can get it at dishwasherfilter.com. i was amazed how c ... Dishwashers

Dishwasher fix water does not go through the spray,. the upper hand an lower hand are clean , the pump does operate to empty the dishwasher . I do smell like some burning smell when I turn the dishwaher on, the water start running for 1 minute or 2 than stop shortly and doesn t reach the arm then the dishwasher becomes hot inside . Thank you


Something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate ... Maytag MDB7100AWB Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

We have a Kenwood KDW8ST2A Dishwasher which is about a month old. The other day we had to pull it out from under the worktop because something rolled under it. When we put it back and went to use it later that day, we got an E1 error code appear and it's been like that since. We pulled it back out to make sure that we hadn't accidently pulled or loosened any of the pipes. We have the manual which does tell us what the error means but it doesn't tell us how to fix it. I'm sure it must be somethin


You can find a manual here ... Dishwashers

Broken Glass Hi! A glass bowl shattered into 10,000 pieces inside out dishwasher. We cleaned out what we could but there is glass stuck in the bottom. It seems like a no-brainer not to run it, but I will ask, will it hurt the dishwasher to run it and let the glass drain out? Is there an easy way I can fix it or do we need to bring in an expert?


Sorry if you've already tried this (and it doesn't really answer your question)... Have you tried taking a damp paper towel to the bottom of your dishwasher - that trick picks up the really tiny glass particules - or a wet/dry vac? ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Rotary water spray device on roof of d/w has popped off - does not appear to be broken but a plastic piece inside location where spray device is connected appears is loose and moves around Can I fix this myself William


Most spray arms are easily fixable. they are held on by screws or brackets. you can just put them back yourself. sometimes they come loose due the vibration caused by the dishwasher operation. ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a neff dishwasher that is maybe 5 years old. im pretty sure there is nothing wrong with it as it was working perfectly fine before i had a plumbing problem a few days ago. after the plumbing problem was fixed the dishwasher doesnt seem to want to fill any longer. it sounds like it wants to work but its just not filling and going thru the cycle. does it just need to be reset or something? im not sure of the model number as ive misplaced the directions for it. could you please help? by the


Look for the connection from the valve to the inlet of diswasher. Check the hot water valve to be on. It is probably closed when anyone working on the plumping. Good luck. ... Neff 24 in. S5443X2 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0839 seconds