Having problems with your Bosch Dishwashers ?

My bosch SHX33A06UC/22 seems to bre leaving water standing below the screen at the end of cycle. Is this normal?


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bosch SHX33A06UC/22 seems to bre leaving water standing below the screen at the end of cycle. Is this normal?


... Bosch Dishwashers

After I run the dishwasher, water stands at the bottom and it smells. I have had the dishwasher for five years. The washer seems to be working properly it's just that water stands at the base of the washer. Is it normal for water to always stand there?


No it's not normal, you are probably having some cloge in the drain pipe, you could try with a pice of wire to pick it up or hose it down, or use some comercial unplaguners like mr. muscle or something like that, i think that this would do the trick ... GE Nautilus 24" Built-in Dishwasher

My Miele Platnum dishwasher is not working. It is flashing "intake/drain" When it begins instead of the normal hearing of water moving around you just hear a humming. My husband and father took out all the filters/baskets etc and made sure everything was cleaned out. They checked the hoses. After that it seemed like it was going to work because it started to cycle normally but now it is flashing again and this time there was water standing in the bottom of the dishwasher. Any thoughts?


Most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drille ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

ASKO 1885 Built-in Dishwasher: The water sump fills normally, but the wash cycle does not start. Althought the timer seems to work, the wash cycle motor won't start up in any wash or rinse selection. The spray arms do not spin - no water is being pumped. At the end of the wash cycle time, the water will empty out of the sump. Thank you. TB


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko 1885 and 2) filling ... Asko 24 in. 1885 Built-in Dishwasher

Dishwasher leaks-can't seem to pin it down to a certain situation-sometimes it leaks, sometimes it doesn't. Also, the filter hole seems to have more standing water than normal


Do you know where it pools the most ? Most leaks occur around the pump housing and the door. over filling with water can cause seepage to a full blown flood. Check your water level switch. ... Kenmore Dishwashers

Whit film on everything at the end of wash. dishes not clean I took off the screen and cleand a bunch of stuff out of the sump. seems the same. it is filling with water draining soap is all gone filled the rinse agent electronics seem to be working. inside of the ss tub is always crummy.. everybody else i know with a ss tub loves it.. im ready to put my old plastic maytag back in


\012Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishes are cloudy and have soap residue. Have cleaned upper &lower spray arm often, as good as posible (find holes plugged). water level & temp. seems normal . Water intake screen appears clean


Clean the spray arm jet holes if they are blocked. Check whether you have filled the rinse-aid dispenser.Check whether arm turns freely when rotated by hand manually. ... Maytag MDB9600A Jetclean II Built-in Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers

My Siemens Hydrosensor dishwasher seems to go through the entire cycle but at the end mainly the top rack of dishes, sometimes the bottom rack is completely covered with a film of junk. It ends the cycle with dirty standing water and is not draining.


It is obvious the drain or pump out is not working. There is a blockage in the outlet. Check the drain under the sink nby removing the hose and making sure the hole is not blocked. The pump in the dishwasher may be blocked. fixing this may not be wit ... Siemens 24 in. SE53200 Built-In Dishwasher

WATER DOES NOT COMPLETELY DRAIN FROM DISHWASHER. TOOK APART DRIN VALVE OTHER NIGHT AND PUT BACK TOGETHER AND IT STARTED WORKING FOR ABOUT 5 LOADS. NOW THERE IS ABOUT 1/2 INCH WATER STANDING IN BOTTOM THAT IS NOT NORMALLY THERE AT THE END OF THE CYCLES.


It is likely that the water pump is feeling its age. Replace the pump. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

I have a Kenmore Quietguard Standard model 587 Dishwasher. It's about 3 years old. Lately, it has been running fine through the first hour and then towards the end, it will pause and the "Hi Temp" and "Heat Dry" like will start blinking at the same time. It's like it is stalled. When this happens, I open up the door and look at the bottom of the dishwasher were the screen is, and I see there is standing water. I press the "Start/Cancel" button to help it drain all the way, which it does, but th


Hi,My take on that would be a bad heating element....the dishwasher is looking for the heat from it and that never happens....so it goes no further and gives the alarm....I would get someone to check that heating element out and replace i ... Kenmore Dishwashers

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

My Kenmore Elite model # 630.16302402 dishwasher isn't getting the dishes clean. A lot of food is still on the dishes after cleaning, especially inside the glasses. There is a white film on glasses and the inside of the appliance. I also just noticed that the upper arm isn't turning. There is about 1/2 cup of water standing in the drain area (not visible until removing the filter tray at the bottom of the appliance). Is this normal? The obvious problem is the upper arm but it seems like the rin


Hello, \015\012 \015\012 ... Dishwashers

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Figidare dishwasher Upper arm not rotating, no water coming from top hole to fill upper arm.Lower arm rotates shoot water up cleaned filter screens. Check ball seems ok by pump, is there a location it (ck ball) should be? My upper arm is not rotating, things are coming out crusty, and it's definitely not getting water to the upper arm. My check ball seems to be plugging the tube the water goes up in.


It seems other posts were correct - The upper arm doesn't spin all the time. Once I learned that, and let the dishwasher cycle through, I saw that the upper arm does spin. So, there wasn't a problem with the upper arm afterall. That doesn't solve ... Dishwashers

Kitchenaid dishwasher - water standing at end of cycle


Less than 2 cups of water in left after cycle complete ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1803 seconds