Having problems with your Bosch Evolution 500 SHE45M06UC Built-in Dishwasher ?

Bosch she45mo6uc/52. came home today and is has a loud hum. looks like it never got water in. the dry soap is just laying inside.


Answers :

The humming noise is either from the pump motor or the water inlet solenoid. One of them is stuck. Take the mopboard plate off the front of the dishwasher and look for the solenoid. It will be a cylinder with two wires attached stuck onto a box in the water line. Start the dishwasher and touch the solenoid with a finger (naturally not the electrical terminals). If you feel it vibrating in time with the hum but do not hear the water running in, the valve is stuck closed. In this case the solenoid may rapidly get hot; that's why you just touch it with a fingertip.

If water comes in and the big motor in the middle starts humming as soon as the fill is complete, then the pump is jammed or the motor bearings are frozen. You'll have to disassemble the pump (from inside the tub) to see what's going on. You should be able to freely rotate the pump impeller and the motor shaft by hand (this is inside the pump; don't confuse it with spray arm, which is spun by reaction from the water spraying out rather than a mechanical connection to the pump motor).

Another possibility is that the water fill level switch is hung up and signaling a complete water fill when the unit is still dry. If this is the case, when you start the dishwasher you may hear the water solenoid briefly, then the pump will start running immediately. Since it has no water, it will just spin at full motor speed. A quick test for this is to pour about a gallon of water into the dishwasher, then close the door and let it run. If it runs normally until it gets to the rinse cycle, then it's either the level switch or the solenoid valve. (Be sure it isn't a pump problem first or you'll have to get the water out while you can work on it!)
Repair Help & Product Troubleshooting for Bosch Evolution 500 SHE45M06UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch she45mo6uc/52. came home today and is has a loud hum. looks like it never got water in. the dry soap is just laying inside.


The humming noise is either from the pump motor or the water inlet solenoid. One of them is stuck. Take the mopboard plate off the front of the dishwasher and look for the solenoid. It will be a cylinder with two wires attached stuck onto a box in th ... Bosch Evolution 500 SHE45M06UC Built-in Dishwasher

Cloudy Dishes My dishes have just recently started turning cloudy with white fllm. This has never happened before and the dishwasher is approximately two years old. There is no issues with hard water, and have used Jet Dry, have tried cleaning it with bleach and vinegar, and have used soap and no soap. Please give me suggestions as to why this would start occurring now. I took off the inside panel and it was full of all kinds of gunk which I since cleaned out. I would like to know how to avoid t


There is a new product out that filters the water going into your dishwasher. the film or cloudy white look is caused by hard water. this filter eliminates the problem and is very affordable. you can get it at dishwasherfilter.com. i was amazed how c ... Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

Dishes and the dishwasher look dirty after they run, like it redistributed dirty water. The door is very dirty/filmy except right under the soap dispenser, like someone squirted dirty water on it but wiped right under the soap dispenser. If I run it a second time with vinegar it gets clean, but that is crazy, esp since it takes 2 1/2 hours a load. I have 2 of them and both are doing it. I have changed soaps, added more soap, used less soap, pre-rinsed dishes, put them in filthy, used jet-dry, no


Hi Mike_wend604,\015\012\015\012I am looking for a used Asko #1504, if you would like to sell yours please e-mail me at [email protected] and put "Asko" in the ... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

I have a GE black panel dishwasher. I am having trouble cleaning the panel. It looks like cleaner has dripped down it but no matter what I use it never looks any better. The panel sounds like hard plastic and is in perfectly good shape. It just looks bad. I've tried soap and water and other cleaners but nothing helps.


There is a cheap way to replace the panel and that is on applianceart.com. They have replacement panels and covers, and even stainless steel. ... GE GSD53 Dishwasher

I have a GE Profiler model # PDW9280N20SS, I used a dishwasher soap from Costco and I think it is not taking any soap from the smart dispenser, the machine is only using water to clean, I rinse all dishes before put then in the dishwasher, you can see by the glasses that they come out with a film on then. I have check the smart dispenser and the soap looks like never goes down. I have removed all soap with paper towels and wash with out any disher 3 times. Is there any special soap I have to


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

GE TRITON dish washer. Utensils are stained after wash. I tried all that suggested solutions like cleaning with white vinegar, make sure hot water flows before it starts. I donot think we have hard water problem and also tried Jet dry rinsing. Nothing is working still i see utensils soap stains and not completely rinsed. I am desperately looking for an answer. I am thinking of is there a way i can test whether the middle tower is really opening up to spray water or not. It might be something els


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

Our Kitchenaide KUDT03FTSS2 dishwasher is not cleaning the dishes like it did when it was new. It doesn't appear to dry the interior and leaves gunk inside, and is noisier than it was when we purchased about 3 years ago. It does not appear to be heating the water - we put a thermometer in there and it read 118. The water out of our tap is hotter than that. The rinse aid has been filled regularly. What should we look for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid Architect® KUDT03FT 24 in Builtin Dishwasher

I wired my Bosch Dishwasher wrong and did a quick wash with it. Later on it stopped working and I figured out I had wired it wrong. I then disconnected it and rewired it. It buzzes for a bit then swishes some water around inside then buzzes again. When I open the door after it says clean it has murky water in the bottom like it was mixed with soap but never emptied. What did I do?


I hope this is not a quiz. Can you please clarify what component did you wire incorrectly inside the dishwasher? Did the dishwasher have a fault that you were trying to rectify.\015\012\015\012it will also help if you provide the full mod ... Dishwashers

Ultra Wash Hi, When I got up this morning, I noticed the dishes were still dirty and dry??  The soap dispenser had popped open but that was about it.  I had some work done on it because it wasn't cleaning the dishes properly about a year ago and they replaced the motor.  While cleaning the kitchen last night, I heard it come on, but now that I think about it, I never actually heard the water start sloshing around. I don't have the owner's manual - I bought this house 3 years ago and I think the


Sounds like your not getting water to it. Turn on and let run for a few minutes then open door and check to see if you have water in it. If not check to be sure water to it is turned on. Check float in front corner of dishwasher to see if mo ... Kenmore 24 in. 15689 Built-in Dishwasher

My sound conditioned Whirlpool dishwasher is real old. It fills up completely with water. It looks like it will overflow, so I stop it. I thought it always started washing from the start. Do they always fill completely up with water, then start washing. I never noticed. I am afraid the water will overflow. Can it? Last time I ran this, it had a real loud motor. I used to hear the motor running from the start, but now I don't, just water filling up to what looks like overflow if I let it. I baile


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in t


I fixed mine works good too, watch my video step by step i put it on youtube ... Karcher G2650HHR Gas Pressure Washer

LG model LDS5811WW/02 has never cleaned the dishes since first installation. Put clean dishes in and they will come out dirty too! Have tried all dishwasher soap types and brands and drying agents. Always scrape and rinse dishes prior to loading. Dishes loaded various ways but problem remains. Repairman says unit is working fine. Also never dries dishes completely. Often leaves soap dispenser completely or partially filled. We are on a farm and have hard water but we have a softener/iron remover


If the soap/detergent isn't completely rinsing out of dispenser, it sounds like water isn't directed the top spray-arm. possible a defective vario motor; as it directs water to the water channel that supplies water to the middle and upper spray arms. ... LG LDF8812 Stainless Steel Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

When I take a glass or cup out of the dish washer after they are cleaned and heat dried, or a day plus from the cabinet to put cold water,too many small bubles are floating on top the water surface, as a soap-like condition; it clears up shortly. The tech told me it is normal. I think it is not normal because I suspect the rinsing is not totally complete because of the water conservation design. Am I drinking soap-water?


Use a rinse agent., such as jet dry. the owners manual will provide you with the specific location as to where the rinse agent dispenser is locatedl ... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

Spray arm, 3rd level, fell off. Flower-like looking ring is still attached to top of dishwasher and arm itself is no longer attached. How can I reattach the spray arm to the flower-looking like ring?I have Frigidaire model number PLD4555FRC0; part # of spray arm, 3rd level, grey is 154478202. I called help line and got someone whose accent I could not understand. I think his name was Victor. He left the line and never came back but, before he left, he said he was looking for the part...why he, t


Unscrew the flower looking piece, there is a white plastic retaining clip inside- press it back together. ... Frigidaire PLD4555RFC Dishwasher

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

The dishes are not clean when we run the wash cycle. It looks like the water flow from the top sprayer is NOT working. The door, when we open it, has undesolved soap stuck in globs on the top of the door. The top dishes are not clean and some of the botom dishes are not clean. We've run some clear washes to see if we can find the problem. The water flow looks suspect. Is it in the electronics or in the water mechanics. I called the repair guy who ususally comes out and says buy a new one! The re


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... LG 24 in. LDS 5811 Built-in Dishwasher

I bought a used GE Triton XL d/w with no manual. It worked great but now it is not cleaning anything, when the cycle is over the soap cup is open but half of the soap is still inside of the cup. I opened the d/w during a cycle and the dishes are wet top and bottom racks so I know it's getting water but the dishes are still filthy. Why is the soap not working? It's like water is spraying everywhere but the door where the cup is!


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... GE Tritonr XL GSD6260JCC Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1924 seconds