Having problems with your Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher ?

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


Answers :

Repair Help & Product Troubleshooting for Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Have mains power to printed circuit board but control panel shows no lights so i cannot start dishwasher


If you have power to the circuit board and lites do not come on then check the door switches in the front panel.The power will not be distributed without the door switches being made. It is a safety factor. If the switches are good then the control b ... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Bosch dishwasher SHX46A06UC/14 that won't drain or cycle. It fills with water. tried changing the main circuit board control panel. That didn't fix it. What next?


... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Dishwasher front panel lights are all blinking in unison. Pump has removed all water from bottom including sump. Pump and lights will not shut off or reset with dishwasher door closed or OPEN. I have shut the circuit breaker off to keep from burning up the pump. Problem continues if I reset circuit breaker.


It would help to know what the make and model of the dishwasher is.\015\012\015\012Most likely the flood switch at the base has been activated. ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standa ... Kenmore 24 in. 16539 Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?


Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Even after ensuring that really hot water is coming from the faucet and placing the unit on the Delicate/Econo setting we consistently get a 2 HR reading. We have also had it where the unit gets stuck on Cycle 1 and we have to reset to go to CL and clear the system of its waste water. Is this a mechanical issue or a circuit board issue.


Did you discover the source of the 2HR reading? Mine's doing the same thing, except the drain pump keeps running and running as well...\015\012Any ideas?\015\012I can't imagine it's anything but the circuit board (for the third time in t ... Bosch SHU5316UC Dishwasher

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

Dishwasher will not start. Clean light flashes. Time display shows --. Manual states "The diswasher has malfunctioned". (Obviously) "Call for service to check heater circuit". Will replacing the circuit board solve the problem?


Hello, welcome to FixYa.\015\012\015\012I understand how vague those manuals can be, very frustrating.\015\012\015\012In regards to the fault, while the control can be an issue and ultimately require replacement...that is a wo ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1474 seconds