Having problems with your Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher ?

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Answers :

Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be good to go. I have no idea why this is not in the instruction manual. A common one is that there us a leak that the dishwasher has detected, normally in the drain pipe.
I had the same problem and followed rstecher and his solution. Removed the kick, light flashing was saying a leak was detected. Tipped the DW on it's side, have plenty of towels ready because the pan will be filled with water. Make sure power is off. Removed the pan and every single one of the clamps was loose. Tightened all the clamps at least 4 complete turns. Dried everything so the sensor wouldn't pick up any water. Put the pan back on and it worked perfectly! Thanks rstecher!
Repair Help & Product Troubleshooting for Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Maytag dishwasher lights but wont run, I can select a cycle then press start and nothing. also the control panel lights stay on when the door is opened


... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

The clean light stays on after running through the normal wash cycle quiet series 300 dishwasher serial no. mdb5601awq3


Some of the clean light's will not go off untill the door is opened, if your light still stays on, It could be a bad door latch switch or a Control board problem. ... Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

The rince light stays on and it wont run, you cant get to any other cycle


Hi there,\015\012\015\012sounds like you may have a stuck key on the keypad. disconnect the power and check the keys on the keypad as well as the pin connector behind the keypad that plugs into the board behind it for any dislogged or be ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

How do I reset a KitchenAid Whisper Quiet Plus? Right now, if I try to initiate a heavy cycle (or normal cycle, or whatever) all that happens is the cancel light lights up and the dishwasher makes a moaning noise. If I let this run its course, nothing happens (i.e., after the moaning stops and the cancel light is no longer on, if I try to initiate a cycle, the same thing happens all over again).


... KitchenAid Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Bosch SHU430UC/06 The dishwasher is stuck on rinse/dry cycle. The run times have been getting longer for the last few weeks. and now the cycle stays on rinse/ dry. The pump still runs and I hear water splashing normally.


Ok first of all there is a drain pump and wash motor pump. which one is running?Then tell me what kind of buttons u have.Are the touch buttons or plastic buttons that move ... Bosch 24 in. SHU43 Built-in Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

Kitchenaid dishwasher mod#KUDS01DLSSO- runs till 54 min left on cycle in normal wash then normal light and add dish light begin to flash with 2 dashes where time should be and locks out


... KitchenAid Dishwashers

When i turn my dishwasher on it runs it wont change cycles and wont wash stays in the same cycle


Hello,This sounds like a bad timer.It could also be a defective thermostat. This problem will become apparent with the water heat option selected. Check by running the dishwasher with this option de-selected and see if it proceeds normall ... GE Nautilus 24" Built-in Dishwasher

About 7 or 8 minutes after setting my dishwasher to run a "Normal" cycle, I noticed that it didn't sound right. The Sensing light and the Add a Dish light were both on. I hit cancel and opened the door to find the inside totally dry and just barely warm. It had a slight smell - probably from the motor trying to run unsucessfully. Is there something I can do to remedy this issue without calling a repairman?


Check inlet water flow to your machine. Try pouring water manuallyin the wash chamber. If machine works OK, it is inlet water problem.Remove the hose and watch for free flow.Clean the strainer attachedto the machine. Beyond th ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Kenmore 665.16529000 When we put the dial to pots and pans the diswasher fills up and cycles through, when the dials moves to normal wash, it fills up and cycles through again. When the dial gets to light wsh we can hear the motor running but nothing is happening, but the soap door opens soon after. The heating light comes on and the inside of the dishwasher gets so hot that it has melted our big plastic tumbler cups on the top rack and makes the counter top extremely hot to the touch. The dial


... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

My dishwasher won't start when push the button , you can't put it in normal cycle and the a very faint light comes on the start but it won't start, lights stay on cycle and then go off. Any suggestions


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2278 seconds