Having problems with your Electrolux EIDW6105G 24 in. Built-in Dishwasher ?

Electrolux dishwasher eidw6105 error 01...no leaks noted under unit. 3 yr old unit. Also leak detector light is green under kick pan. Not responding to Electrolux CSR instruction to hold Heavy Wash button down for 10-15 seconds or other poster's recommendations to hold down any two buttons down for 8 seconds. Currently have a space heater running air under to hope to evaporate any water or condensation.


Answers :

Repair Help & Product Troubleshooting for Electrolux EIDW6105G 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrolux dishwasher eidw6105 error 01...no leaks noted under unit. 3 yr old unit. Also leak detector light is green under kick pan. Not responding to Electrolux CSR instruction to hold Heavy Wash button down for 10-15 seconds or other poster's recommendations to hold down any two buttons down for 8 seconds. Currently have a space heater running air under to hope to evaporate any water or condensation.


... Electrolux EIDW6105G 24 in. Built-in Dishwasher

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

I have a Frigidaire Gallery Series dishwasher (model. GLD3450RDB0) that always displays the "lock" icon under the no heat dry button. I am able to get rid of it by holding the button for 3 seconds, but I am still unable to select anything or get the dishwasher to start afterwards. As soon as I close the door, the unit locks again! What can I do?


Have you tried unplugging the dishwasher for a while then .. Trying it again.. If the problem still persists have a cleaning done to the control board and touch pad inside and if still the problem persists then i doubt whether the problem is that the ... Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

EDW5505EPS Electrolux Dishwasher. One cycle light stays on, but the other lights will not turn on when buttons are depressed. Unit will not turn on at all. I assume the control board is bad? How difficult is it to replace the control panel? Just remove the screws holding the stainless panel on? I assume the panel simply plugs in.


Hello,\015\012Have you tried holding the cancel button down for about 15 seconds as these units can sometimes get stuck in a cycle. Try this anyway first.\015\012\015\012Hope I helped. ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

My Samsung DMT800 series dishwasher has had the main control board replaced under warranty three times since I've had it. The problem: The unit won't activate via the touch buttons until I pull the plug for a second and "re-boot" the device. It then works for a few days or a week and fails again. The last board was replaced two weeks ago and it has failed only once. I'm waiting for it to fail again before I call Sears home services again. Has anyone else had this issue? My repair man has said y


... Samsung Dishwashers

Setting the water hardness system on Beko DWD 4310W. The handbook instructions seem to be wrong. There's no display panel on the machine as it states, and it tells you to press and hold Start/Stop button and switch the On/Off button, release the On/Off button, press and hold Start/Stop button for 10 seconds,( which you are still pressing anyway!) Then it says the last setting will be displayed on the panel for five seconds. But no panel.Totally confusing.


... Dishwashers

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

For my Kudi01dl model dishwasher, the rinse light is on, but the unit will not respond to any buttons being pressed and won't turn on. When I press any buttons, two horizontal lines show in the front, but go off as soon as I let go of the button. Is there a ways to reset the unit? Everything was functioning fine the last time I used it. I use it about once a day. The problem started when I heard sounds coming from the unit, very loud motor sounds. The door was closed but I had not turned


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

I have a Campbell Hausfeld RBPW1810 pressure washer, It has two detergent tanks. I cann't get either to work. I just purchased the unit in June if this year and this is the frist time I am useing the unit. I followed the instructions (low pressure position on the nozzle) and the detergent came on for two second then stopped (only water then). What am I doing Wrong??? Rich From Alqonquin, Ill


Sometimes thinning the solution will help, but in any case make sure the line from detergent tank to pump is sealed, otherwise it just sucks air. I use a small hose clamp at pump. let us know ... Campbell Hausfeld 1800 PSI Electric Pressure Washer

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Crystal wash and rinse only buttons flash and can't get any other button to work. Tried turning off circuit breaker and holding down set/cancel button but goes right back to the two buttons blinking, also in this mode dishwasher makes sounds but no water. Help! Thanks.


Without a model number this is my best attempt at trying to help you with out it. In the bottom of the tub look for either a float assy or a finger like thing sticking up from the bottom. If there is a float gently push it down first ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Dacor MDV24 dishwasher. I press cancel to turn it off and it works but after approx 10 seconds the start and normal button comes back on and beeps. I tried shutting the breaker and holding the cancel button for a long time but it still always comes back on. Got any suggestions?Motherboard or faulty buttons?


Hello &\015\012Welcome to FixYa\015\012\015\012If you have\015\012also checked the door lock-latch assembly and that is fine then yes it is the\015\012control board that is bad and needs replacement. Please get back to ... Dacor Millenia MDV24 Built-in Dishwasher

Matsui dishwasher Matsui MS452S slimline - second wash light flashing and unit doesn't fill. Tilting it backwards allows water to leak out from the left rear corner then it runs correctly for minute or two before numerous beeps sound and unit cuts out with light flashing again. How do I get into the base to see if there are any leaks? Unit less than 2 yrs old.


... Dishwashers

Can't start the dishwasher, lock button is lit up. Tried to hold down many buttons for 3-5 seconds, but lock button continues to stay lit up. Tried resetting the power to machine, but nothing changed. Please help.


Hello Albert, On the Jenn-Air dishwasher you have, you have to hold down the "Heated Dry" button for 3-5 seconds to unlock the control panel.\015\012\015\012This should unlock the controls so you can again use the dishwasher normally. ... Jenn-Air 24 in. JDB1090AWS Stainless Steel Built-in Dishwasher

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

Maytag Quiet Series 300 Contol Lock Light On does not turn off by holding heated-dry button for 3 seconds as manual states.


... Maytag 24 in. MDB9750AW Dishwasher

Electrolux dishwasher buttons light up but unit doesn't turn on


Sorry to hear that you are having problems with you appliance.That failure is caused by a bad circuit board or the buttons are not working properly, quite hard to diagnose without looking at it. Do you get an error code? I believe it ne ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

Control panel is locked. no buttons work when pushed. door panel says to push and hold ''heat dry'' button for 4 seconds to clear. nothing happens. this is on kenmore ultra wash dishwasher


Try unplugging the machine and wait 5 minutes. Plug it back in, the problem should clear. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0954 seconds