Having problems with your Electrolux EIDW6105GW 24 in. Built-in Dishwasher ?

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Answers :

Hi
\015\012\015\012

The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope this\015\012helps...please post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

SGV55M43EU - The machine does not spray the water even if the pump works. The only way to have the water spray is to add water manually directly inside the machine. I checked the inlet valve (acqua-stop) , it seems to work. many thanks, Alessandro


... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Water pressure? I read somewhere that low pressure of the incoming water will make it so that the items on the top drawer will not be as clean. I don't see how this can be the case, as I thought that the way the washer worked was that the washer filled (at whatever speed) and then the machine itself pumped the water through the system at the appropriate pressure. Please clarify.


Mom...not true. The water fills the machine which then uses its own pump to spray the dishes with the water/detergent. If your dishes are not getting clean, use the recommended amount of detergent. Hard water will require a spot treatment like Jet ... KitchenAid KUDR01TJ Dishwasher

I have a 5 year old KUDI01FLSS and it fills with water but does not spray water arround durring cycle (it does sound like it is working though). It will also drain the water when I hit cancel. I cleaned the filter screens but they were in good shape. I now suspect that it is the pump assembly. Anyone know if that is the direction I should head?


Yes, you are on the right track, the pump may have something in it clogging up a little bit so that it doesn't have enough water pressure to spin the spray arm. Clean out the pump and see if that helps is your best bet since it is working otherwise. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

Ge dishwasher im having a problem with a dishwasher in a  home i just bought....it worked fine at first, now it has basically two cycles, off and wash....it will not try to fill, or pump out, it just washes.....the model number is gsd1100g02ww.  i took out the timer assembly and  found nothing  visibly wrong...but hey, i can fill it  up  myself with water and shop vac  it  out and it works"i tell my wife" i wont  tell u what she told me in return......any help i would appreciate.


Try taking the dishwasher out so u can see the bottom, or if u cant, pull the bottom front plate off, remove the plate, ull see a pump looking peice, small with main water line hooked to it, disconnect it and pull it off, u will need to take it ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Dishwasher fills with water, but spray arms don't spray water or spin. As the cycle moves forward, water is eventaully pumped out (so the pump is working). i've selected different cycles with the knob on the front of the machine but they all work the same.... no swishing with the spray arms. When the cancel button is pushed, the water is pumped out... as it should. Thanks for the help.


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

My ASKO 1805 Dishwasher started to smell weird and white smoke came from it. I turned it off, but after I turned it on again it just keeps pumping water in and out, I can't get in contact with it (None of the indicator lights are working and it is not reacting to any commands) In addition the safety feauture that is supposed to stop all operation the moment the door is opened is no longer working. (i.e. even with the door open it is still pumping water) Does it sound like an expensive repair? (


Hello,\015\012\015\012Welcome to FixYa. Based on your description ( specifically the white smoke and smell ) I would suspect the control board is faulty. \015\012\015\012If the unit does not stop when the door is open can be r ... Asko 24 in. 1805 Built-in Dishwasher

GE Profile Dishwasher about 7 years old. everything seems to work door locks the machine trys to pump water in but it can't. I put water in thhe bottom of the machine and it does work a little but verry weak spray. It does pump out fine. Help


The washer doesn't pump water in--plumbing water pressure forces it in when the water inlet solenoid opens the valve. Check the water inlet solenoid--they are a common failure point. Look under the front of the washer behind the panel to find it--jus ... GE Dishwashers

ZANUSSI Da 6341 dishwasher, Flooding in middle of cycle. Sometimes at start of cycle (5-10 mins) washers floods and water comes out of front. If i move timer to end of cycle pump works and water is pumped to sewer. This doesn't happen every time. Sometimes cycle works perfect and after that doesn't


... Zanussi 24 in. DA6141 Built-in Dishwasher

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

I have a GE roll around dishwasher, Model GSC3200Z03BL. It worked one night, did not work the next. After hooking intake/discharge hose to faucet and turning to start, no water is pumped in. Only a humming noise much like something is stuck preventing pump from allowing water in. What to do? Appreciate the assist.


First off.. the pump does not let water in.. it takes water from your sink faucette via the hose and allows it to enter the DW via an inlet electrically operated valve. If that valve is not commanded by the control system to open, then no water will ... GE Dishwashers

DWF 415 Ikea Whirlpool Dishwasher has constant green blinking light. Drain pump works ok (as it will pump out a jug of water if I tip it into it!) but no water comes in. Cycle stops about 30 seconds after thre is no more water to pump. Any ideas on how to fix?


Anyone got an answer to this, as I have exactly the same fault. \012\012\012Dishwasher appears to switch on OK, then after a short time (20 secs?) the pump noise stops and the green light flashes - it seems to e a sequence of 7 flashes, t ... Whirlpool GU2400XTP Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1634 seconds