Having problems with your Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher ?

Is there anyone out there that can HELP!!!!.I have the f/p dd603h model and have had nothing but problems with it the latest being the bottom draw is a struggle to pullout+top draw keeps beeping very very annoying!!!!.Have tried to locate actuators by pulling out bottom draw but not quite sure what I'm looking at,and are they easy to replace?


Answers :

The source of the problem could be the power filter board at the base of the dishwasher under the bottom drawer. This supplies power to both the drawers as well as operates the actuator motors for the drawer lid seal.
You could replace the power filter board and see if there is any difference. However, the actuator motors need to be very carefully aligned to get the dlid seals to sit properly and not cause leaks. This is a technicians job if you are not very comfortable with mechanical repairs. Make sure mains power cable is taken out when you are working on the dishwasher.
Repair Help & Product Troubleshooting for Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is there anyone out there that can HELP!!!!.I have the f/p dd603h model and have had nothing but problems with it the latest being the bottom draw is a struggle to pullout+top draw keeps beeping very very annoying!!!!.Have tried to locate actuators by pulling out bottom draw but not quite sure what I'm looking at,and are they easy to replace?


The source of the problem could be the power filter board at the base of the dishwasher under the bottom drawer. This supplies power to both the drawers as well as operates the actuator motors for the drawer lid seal. You could replace the power ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher and paykel DD603ss ,bottom draw does not slide out easy,,,,


Hi- Most likely the lid is stuck in the down, or partially down position. This is usually caused by the lid actuators (motors) not returning the lid to its full up position and therefore the drawer top is dragging on the lid gasket. Replacing t ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher paykel DD609 diswasher - top draw does not drain properly. Water build up in bottom of the top draw even when bottom draw is used.


It is usually due to a small piece of broken glass or plastic blocking\015\012the little propellor that pumps the water out, (think of the little\015\012paddle in Nemo's tank)\015\012You need to remove the bottom of the machine, undo one screw ... Dishwashers

I have an older Bosch dishwasher I just hooked up in my condo. WHen a cycle is done there is no water is located at the bottom of the inside of the dishwasher, yet 2 days later water will drip on the floor (with the dishwasher door closed) and I'll open the dishwasher door and therewill be 2" of water at the bottom. The flexible water discharge hole located in the sink base is located at the top of the base cabinet, and the hose runs completly 100% downward from that hole to the garbage disposa


When you empty you sink, some of the water is going down the drain hose of the dishwasher. take the drain hose up as far as possible in a swan neck ... Dishwashers

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Turn water on then actuate wand trigger. Pressure washer leaks when wand trigger is actuated and has very low pressure/flow output. After releasing trigger the pressure cycles on - off at approx 1 second interval. I suspect that the plasstic oulet tube is leaking causing low pressure leak out of bottom when trigger is actuated and causes pressure switch to cycle when the trigger is released. Any Help? This pressure washer is approx 18 months old!


You gave a very close solution yourself for the problem. But other leakages can cause such symtoms.Forexample a leaking head or a leaking chemical inlet. These can be caused because the spill valve (pressure control valve) is stuck. When this valve s ... Karcher PSI Electric Pressure Washer

My kitchenaid dishwasher has a bottom rack allignment problem. Especially when it is fully loaded the right rear pair of wheels often slips down off the bottom track and makes rolling the loaded rack fully in very difficult. I've already had a serviceman come out and he sent me a new bottom rack and set of four rollers and that improves the situation but does not eliminate it. Any similar complaints? Any easy fix before I call the service guy again?


Hello. If you have a new rack and new wheels the only fix to your problem is to either replace the dishwasher all together or NOT put as many items in the bottom rack. I am always bothered when anyone tells me they were sold a new rack because the ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

On 2 door dishwasher model DD603 bottom draw is very hard to slide out or in. Can i remove draw to inspect and oil draw runners?


Hi- Most likely the lid is stuck in the down, or partially down position. This is usually caused by the lid actuators (motors) not returning the lid to its full up position and therefore the drawer top is dragging on the lid gasket. Replacing the l ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

My 14 yr old Magic Chef Model DU4K seems to be leaking (it is dripping into the basement just under where the dishwasher is located). it started when the arm at the bottom of the dishwasher did not seem to be moving so my husband took off the bottom "grill" to see if maybe there was something under there preventing it from spinning. It started to leak when he put it all back together (the bottom arm is still not spinning)


Being 14 years old I dought if spares are still available for this machine personally at 14 I would rather replace the unit if you are not in a possition to replace it you could advise from your local appliance repairs as to weather parts are availab ... Dishwashers

Our 8 year old integrated 2 draw dishwasher (top draw) has a problem on the rinse cycle and constantly beeps and water at the bottom of the draw remains. I have cleaned out all the grit and stuff residual water and tried to use again. But alas there appears to be a blockage still on the rinse cycle. Can you help or do I need to get a plumber? Thanks...Louise


Sorry i lost you my breaker tripped ... Dishwashers

Maytag MDB7100AWW Is not throughly cleaning dishes on both top and bottom racks. Some food particles may be flicked off with a finger after the wash cycle. Some dishes are cleaned and in other locations on the same rack it is not. It is not throughly rinsing and leaves a film. The top and Bottom spray arms and bottom filter have been cleaned


Hello there:I will post this in 2 seperate post's due to the length of this answer and possiable solutions ok?\015\012\015\012 \015\012 If your dishwasher is cleaning poorly, check these:\015\012 ... Dishwashers

Top draw dead bottom draw works fine


The heter plate has a fuse molded in it change the heater plate ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Have a rental property with F&P two draw dishwasher aprox five years old. Apparently bottom draw is holding water - what do you think?


Could be many reasons for the bottom drawer to hold water.\015\012\015\012It could be leaky top drawer causing water to collect in the bottom drawer. Check if water collects when top drawer is running.\015\012\015\012It could ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Top draw works, bottom draw not working. No noise and no display


... Fisher and Paykel 24 in. DD603MFC Built-In Dishwasher

WHEN RUNNING A CYCLE ON TOP DRAW THE BOTTOM DRAW WILL FILL UP WITH WATER NOT DRAIN


The drain hose going to the kitchen sink is blocked. If you have an insinkerator in your kitchen sink then run it first. Otherwise take the dishwasher hose out from the sink outlet and run straight into sink to see if any difference. ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

Fisher Paykel control panel to far left side has a film on it that chipped off - showing a shinner stainless steal under it. I guess this is a coating of some sort. Dish draws are 4 1/2 yrs old. Mild det on them only. Only bottom draw has the cracking on it. -- can that be fixed or just has to stay ugly.


You can buys the parts that look chipped/ broken and replace them. Panel parts are very easy to replace.\015\012\015\012Check out which parts you need from the parts manual and order from the local fisher and paykel distributor.\015 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bottom draw alway ends up with residue water remaining in the draw?


What sort of dishwasher is it.if its a fisher and paykel then that seems to happen a lot its not a problem ... Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

Fault9 on bottom draw draw will not slide in or out


... Fisher and Paykel DD605I Dishwasher

I have a LG LDS5811ww dishwasher that is leaking from the bottom of the door. Feels like the bottom seal has been pushed in. Is it easy to fix/replace?


What happens is the cheap tin on the door gets bent out over time (pushed down) when you load and unload the machine. You can probably grab hold of the inside bottom of the door when its open and with gentle force pull it up back into its origina ... Dishwashers

My new Frigidaire dishwasher (FDB2415LFC) has not been used but is out of warranty. It has a leak with water dripping from two connectors (may be the heat coils) attached to the bottom of the dishwasher (located in the center). Why would water be dripping from this location and what is the repair solution? Should I try to return the dishwasher and obtain a replacement?


... Dishwashers

Cannot turn my fisher and paykel dishwasher off..keeps beeping and motors are running in both draws. I have taken the bottom draw out and it is dry.. I can only turn it off if I turn the house mains off (then everything else is off!!)


I am assuming you infer that the bottom of the dishwasher is dry when you took the bottom drawer out. This means the floodswitch located on the power filter board at the bottom of dishwasher might be faulty. Do you get any Fault code on the display. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Leaking water from bottom draw


To put machine into test mode:\015\012Press and hold keylock, then press and hold start button. Hold both in until machine beeps (if you have display, it will show all symbols). Press power button- display should now show HO. Press start button until ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0522 seconds