Having problems with your Frigidaire Dishwashers ?

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Answers :

Looks like a number of things are happening.
\015\012
\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.
\015\012
\015\012I am assuming you have turned the mains power off and on.

Hi
\015\012\015\012

Thanks for using FixYa. To resolve this press and\015\012hold the AIR DRY or RINSE ONLY button for 15-20 seconds. Please accept the solution if the\015\012issue is resolved or post a comment for further assistance.
\015\012\015\012


\015\012\015\012

Thanks
\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Sometimes I can run the dishwasher with no problems. Sometimes i will run it and leave the house and come back 5/6 hours later and it is still running on the wash cycle but it is only putting out heat and no water. So its drying up the soap on the dishes and not really washing anything, and it get stuck on that cycle


... Magic Chef 24 in. DU4500 Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Clean light blinks 7 times after going through complete cycle up to heated dry. ive reset it using the heated dry/normal wash buttons. so it will run until it has to dry then i get the error. how do i fix?


This error says that there is a fault in the heater circuit. the heater circiut goes thru the doorlock assembly, thermostat(if equipped) then heater and back to the board.\015\012\015\012do you see or feel and rough spots on the surface ... Kenmore 24 in. 17014 Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.


... Bosch 24 in. SHU43 Built-in Dishwasher

KENMORE MODEL # 363.16222100 Hello - my dishwasher (model# above) is currently filled with H20 and will not drain/work. When the knob to select the dishwasher cycle to begin is turned, it just 'clicks' and does not engage the washing cycle. When I tried to just let it run the cycle as is to 'restart', it had an electrical odor to it., Currently the knob is at the 'Rinse & Hold-(Heated Dry Off)' part of the cycle and all dishes have been removed. I would appreciate any assistance available. Thank


Either the motor is locked up or the control failed. You will need a service visit. If it is over 10 years old, I would buy new. ... Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Dishwasher runs forever - I have to manually drain it by pushing 2 buttons on front at same time - never gets to dry cycle - makes no difference what wash cycle i am in - however the rinse & hold cycle seems to work


Hello,Welcome to FixYa ... Thermador DWU244 Dishwasher

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

I have a Frigidaire Ultra Quiet II dishwasher that gets stuck in the 6:00 position (between light wash and drying) during the cycle. It also gets stuck right before the drying cycle. It will proceed with the cycle if I manually move the dial. The heated drying feature is also not working as well. Do you have any suggestions? Thank you for you time, for it is appreciated. Best Regards, Scott G.


... Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

Ref: NEFF Dishwasher S5555XOGB/70 (FD No. 8602) Problem: Does not drain at end of wash cycle. Checks/Symptoms: 1. No blockage in whole of drainage system, system and filters are clean. 2. Pump does operate mid wash cycle ? drainage tube can be felt pulsing and pipe gets warm right through to the main drain connection at the ?U? bend. 3. At end of wash cycle the pump appears to still be trying to run but there is no flow, even when the door is opened. If machine is emptied by hand the pum


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1520 seconds