Having problems with your Frigidaire FDB1502RGS Built-in Dishwasher ?

White wire connecting heating element burnt plastic covering.


Answers :

Repair Help & Product Troubleshooting for Frigidaire FDB1502RGS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

White wire connecting heating element burnt plastic covering.


... Frigidaire FDB1502RGS Built-in Dishwasher

I have washed and rewashed my dishes with no soap and my glasses have a horrible white film and any of my plastics now have white film almost as if the soap is not rinsing off. I have resorted to hand washing and some of the glasses seem to be etched with this white residue....difficult to remove. Please help! I have read possible heating element problems but I just ran the dishes thru a wash cycle with no soap and when I opened the door the heating element seems to be functioning fine -- all


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Replacing heating element in Kitchenaid dishwasher KUDI01TJBL0


... KitchenAid KUDI01TBK Dishwasher

I want to remove the white plastic wheel that propels water into the circulating arms. It is held with one screw which I cannot seem to be able to loosen. This white plastic wheel has 2 small holes in the surface which are perhaps there for some special tool to hold the wheel stationary in order to loosen the screw holding this wheel in place. Underneath this gray plastic housing is the heating element. I want to remove it in order to clean accumulated deposits of gunk.


It's reverse threaded. ... LG 24 in. LDS 5811 Built-in Dishwasher

My Frigidaire model FDB1050 will not heat the water. The heating element checked out at bout 14 ohms but the approximately 8" wire from the heating element to what I think is a thermostat is slightl


Hello preslncon - The black button that you are referring to is more than likely the Hi-Limit Thermostat. The Hi-Limit Thermostat will open and stop power from reaching the heating element. The Hi-Limit is not resettable, and if it is open, it wou ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

Dishlex DX302 Hi mate, I have the smae problem with the water not heating . I have checked for the burnt out relay (as is common)but no go. You mentioned you could send the service manual and wiring diagram for this model to the previous user you helped out. If you could please send it to me that would be grate as I want to test the heating element. [email protected] Thanks Jason


... Dishwashers

Kenmore dishwasher The dishwasher isnt cleaning the dishes and is leaving a white film on the dishes. I just took everything out and noticed the heating element on the bottom is covered with white chalky kind of stuff. Any clue?


If\015\012your dishes or glassware appear with a white film or a white powdery residue or spotted following a complete\015\012wash cycle, adjusting the amount or type of detergent you?re using and\015\012adjusting your hot water heater?s ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a frig/electrolux gallery series dishwasher: model GLD2445RFC0 serial # TH72896159. On the ceiling of the dishwasher is a gray plastic arm that snap onto a round gray disc that screws into the ceiling. It will not stay connected to the disc eventhough I snap it on with a round white plastic doughnut kind of cap. I have replaced the gray arm in the past because the orig. one fell and melted on the heat ring. This one has : 1546496 1546079 CAV 2 >PP+20TF written


If you go to searspartsdirect.com and type in 154607802 for the part #, I'm pretty sure that's what you are looking for. I broke the exact same part and it's what my husband ordered as a replacement. ... Electrolux Dishwashers

The heating element does not function; it use to. Also, the detergent dispenser door does not open during the wash cycle. So, how do I determine the cause of the problem - burnt out element, bad switch, etc? Are the issues possibly connected, or separate? Thanks in advance!


Hi,\015\012Probably two different problems....\015\012\015\012Dishwasher Repair Problem Detergent Cup does not O ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

While installing maytag dishwasher mdbh949awb, a wire became unplugged under the machine; noticed it dangling down after all water, drain etc. were connected. It's a brown wire; 2 strand; it has a white plastic plug/connector on the end. Any proposed solutions, short of removing the machine and starting over, would be greatly appreciated Thanks.


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

I have a dishlex global 300 on which I removed the front cover a black wire came loose and I didn't know where it came from thanks to jyackle5 I have fixed that issue. The problem I have now is the eco light flashes and that's it (nothing else functions). I removed the front panel as the bottom door seal had blown and junk oosed behind the front panels I washed the junk out and cleaned the hole washer while I was at it the bottom of the washer (where the heating element is) over filled so I tipp


Easy fix, Use a bit of force and pull the dishwasher out.Get a few towels and tilt to the left. Water will drain out. Push back in. wait 10 mins and turn on.\015\012\015\012\015\012\015\012Regards ... Dishwashers

My frididaire dishwasher is leaking at the heating element/burner (red wire). I have tried to tighten the connection from under the dishwasher but it continues to leak (very slowly). The clasp used to tighten the element does not hold it's tightness and will become too loose if tightened all the way. What do I do?


Replace the heater element. ... Dishwashers

Dishwasher started having water pour out the front. The heating element dropped and burnt a hole in the plastic.


... General Electric GHDA485NCS Built-in Dishwasher

Water leak at heater element connection seal, rusted connection


... Whirlpool DU1055XTSQ Built-in Dishwasher

I replaced the heat element on my dishwasher and now it shows a bad wiring or bad element code where can i get a color coded wiring diagram


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I am installing a Kenmore dishwasher model 13743. I have direct wired the washer?s terminal box wires to the wall power via a BX wire and the washer doesn?t respond. None of the panel buttons are active. With a multimeter, I find that there is voltage on the wall wires and on the dishwasher end of the BX cable wires that hard wired to the wall current. Even though, when I connect the dishwasher?s terminal box wires to the BX wires as directed in the Installation Instructions (white to white,


Next step to check the door switch...the door must close and the switches on the door must close to send power to the control...let me know ... Dishwashers

I wired a ge dishwasher ..white to white and black to black. the ground..green wire a screwd to the dishwasher.. turn it on and everything worked ok til the pump came on and the the black to black connection overheadt and starte a fire.... what did i do wrong...note my house wire has only white and black...thanks


Well, hard to say at this point. Your wiring sounds correct, but there may be some other stuff going on which you may have not anticipated. First off, what size breker is attached to the wires you connected to the machine. Most household machine requ ... Dishwashers

We need to connect it back to the built in wires in the dishwasher. We need to know what colours or wires connect to the flat gold metal plates, there is a black plastic case that slips on and then 3 plates underneath and on the top, but not quite sure if that is correct. Then there is still wires that are loose that need connecting. Part NO. C00059727 Copreci - Merloni 1 160010266 TD02 0008


... Dishwashers

HI. Trying to install a LDF6920ST Dishwasher. Question about the wiring. The wires coming out of the machine are Black, Green with a yellowish stripe and White (the white one has a label attached to it with a "N" on it). The plug wires are 3 side-by-side. They are gray, green and gray. Which wires do I connect with which wires?.


... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

I'm attempting to reuse a Maytag dishwasher motor for a bench grinder. Since this is a reversible motor, I'm not sure how to connect the wiring to a simple switch so that it works in one direction only. The motor has 4 wires: blue, gray, red, yellow. Not sure which to connect to the hot (black), return (white) and ground (bare) wires from the romex and can't find a wiring diagram online for this dishwasher. Any ideas? Thanks.


... Hobart 29 in. AM15-1 Free-Standing Dishwasher

Replacing heating element


It's a reverse screw, meaning to loosen it you have to turn it the opposite way you would loosen a regular screw. ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Whirlpool model GU2400XTPQ7 (Canada) plastic tub has discoloration from heat element......plastic directly under the element has dried out and cracked....it almost looks like it has been eaten away......now I have a leak! Virtually impossible to fix without replacing the entire plastic tub. Of course because the machine is four years old, the warranty has expired. Is this a common problem? Heard of this before?What now???


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0630 seconds