Having problems with your Kenmore 13742 / 13744 / 13749 Built-in Dishwasher ?

Kenmore 13749, wash cycle is not working

\015 Kenmore 13749,\015\012 The washer did work for 2 loads without a problem. Now the dishwasher fills with water, does not run the wash cycle, panel lights on without blinking, push the cancel drain button and water drains out. This a new wash disher. Sears technical support states that might be an install problem.Yes I did install it, yet I would think if it was install problem it would not have run 2 loads nor would it fill or drain. But I am not an expert. I would appricate any advice you give.\015\012Thanks\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -

... Kenmore Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous

... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.

... Kenmore Dishwashers

My Kenmore ultra wash dishwasher model 665.1374 will only work if I press the restart button. When I do it goes to pots and pans with the drying cycle light lit. I cannot get the smart wash, normal wash, or quick wash buttons to work.

... Kenmore Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th

... Kenmore Dishwashers

Dishwasher inoperative The lights that indicate the wash cycle are flashing along with the 6 hour delay light. I have tried to cancel the cycle but it does not work. I shut off the breaker to try and reset the operation and that does not work. The dishwasher will not work and I cannot reset or cancel the flashing operations. Kenmore Quite Guard 3 Model 587 15072200

... Kenmore 15522 Built-in Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402

First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Kenmore model 665.16509200 Does not clean very well and now dry cycle not working. Wash cycle takes almost 2 hours, and still dishes had gradoo and white detergent on them, even ones that were clean when they went in. The drying coil had plastic melted on it once before, so that could have caused that malfunction. I am not so concerned about that, it is the dirty dishes after 2 hours that is driving me nuts. The short wash cycle leaves EVERYTHING dirty, so I just quite even trying that.

... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene

... Kenmore Dishwashers

Kenmore Elite Quiet Guard Undercounter Dishwasher 66513482K902 the wash cycle lights dont work i can not see what cycle it is on

... Kenmore 1348 Builtin Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.

... Kenmore Dishwashers

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?

... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore dishwasher model # 587.15103800 wash cycle won't start. It fills with water and stops. A few minutes go by and it drains. Motor is working. Any ideas why the wash cycle won't start?

... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore 13749, wash cycle is not working

... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim

Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Kenmore Ultra Wash built-in Diswasher. The flap on the detergent door does not open as it should during wash cycle. Also, I thought the rinse aid was empty so I went to fill it and its obvious that it has not been dispensing either. Otherwise the dishwaser seems to work ok, but we have hard water & I've tried everything and still have residue on dishes.

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Water coming out front of dw at start of wash cycle. I leveled the unit. no luck. if you open the door during fill cycle the water does not shut off. also, may be a problem with float shut off working properly. what should I try next? Kenmore Elite 16579

Hi \015\012Check float to insure that it is free to move, it sounds like the dishwasher is over filling. That is assumed that you have not changed the type or amount of detergent being used.Also there is a probability tha ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.

The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.

... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the

There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe

... Hobart AM14-253 Free-standing Dishwasher

We have a Kenmore Ultra Wash Dishwasher, several years old. The lock light went on yesterday and we could not put it on wash or anything. We hit cancel, unplugged the machine, left the door open so it would stop the cycle...nothing worked. How do you get the lock off when it goes on like that? I just went into the kitchen, shut the door and the lock was off, strange.

There is a key (usually the dry key) that needs to be held for 4 seconds to turn the child lock on or off. If it comes on again try holding this key for 4 seconds.If it was pressed and held by mistake this could cause the lock to activate ... Kenmore Dishwashers

Kenmore ultra wash quiet guard dishwasher sensor light stays on; cycle will not move past wash. Heater element does work!

... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny

... Dishwashers

The water does not run into the dishwasher, though the heating element works, and it goes through the cycle. The dishes are not getting washed. Also the ON light is not working. model number Kenmore 6651676569.

Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1457 seconds