Having problems with your Kenmore 16483 Built-in Dishwasher ?

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.


Answers :

Repair Help & Product Troubleshooting for Kenmore 16483 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.


... Kenmore 16483 Built-in Dishwasher

I tried twice to wash the dishes and it just stops and a red light comes on over the cancel button the dishwaher is only 3 months old. whirlpool dishwasher model DU1010XTKQ2 turn on to wash it will run for about 15 minutes and cut off with red light over the cancel button


... Whirlpool Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

I have a Ge monogram that I purchased in 2003. It is a stainless steel with a touchpad/ buttons on the front. No dials or displays. when I start the dishwasher after about 3 min it switches to China Crystal mode and the red light above that blinks and it stops washing... I canceled the job by holding down the start button for 3 sec it just stops after 10 secs and turns off...


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

My dishwasher wont run when i push the start / cancel button the washing light comes on and blinks ,but the dishwasher does not turn on . i put in a new control panel and it still does the same thing.


Check the water level switch/ pressure switch.Control panel may not have full control. There may be yet another board inside! ... Frigidaire Dishwashers

My westinghouse 915 dishwasher has frozen mid program and the prewash in the middle is flashing i can cancel but when i try to start the lights for prewash on the left and the normal button stay on for 5mins the the pre wash flashes again i,ve turned of at power supply to thx


... Westinghouse MDB631 RF Dishwasher

I have a Kitchenaid Dishwasher Model KUDC25CHSS1. (Manual says KUDC25CH). The Delay Hours button is stuck on 2 hours. The manual says to cancel it, press it until no lights are on, but when we press it, the Child Lock light comes on. I tried pressing Energy Saver Dry to cancel the Child Lock, but that didn't cancel it. I tried turning off the circuit breaker for 5 minutes, but the same light(s) come back on when I re-set it.


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Dishwasher model 665.13763K602 SER FU3009053 the control panel on the front of it has 4 lights on and won't turn off. they are the pots/pans, norm wash, china, and fast wash. the other 2 lights will not turn on - smart wash and quick rinse. I cannot make the dishwasher start. When I press the cancel button, it does something for about 60 sec. then stops.


... Maytag Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1936 seconds