Having problems with your Kenmore Dishwashers ?

Installing used dishwasher. All hooked up but there is no water getting to the wash basin or tub.

\015 It's not getting water. The water line works\015

Answers :

The solenoid valve controlling the supply water is not opening. This could be caused by no power to the solenoid or a failed solenoid.
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Installing used dishwasher. All hooked up but there is no water getting to the wash basin or tub.

The solenoid valve controlling the supply water is not opening. This could be caused by no power to the solenoid or a failed solenoid. ... Kenmore Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.

Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a

The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

It seems that not enough water gets into the tub. There is no kink in the water line. If you manually add water it drains out before resuming wash cycle. The water doesn't get around to wash the dishes let alone rinse the soap off the door!

If the machine has stopped half way through due to switching off or power intruption this could happen.\015\012\015\012So allow the machine to complete the cycle. \015\012Do no worry running it empty.\015\012\015\012It s ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Bosch Integra SHU 9955US/12 - when we start wash cycle, the detergent dispenses and the tub fills with water, but the wash cycle never starts (never spins spray bars). Seems like timer is counting down, though, but doesn't start "washing". After waiting awhile, we are able to use the "Cancel/Drain" mode to drain the water. The drain filter in the bottom of the tub is clean.

Sounds like your motor is burned out. The drain motor and wash motor are seperate on your machine. You can check for power going to the motor, but to do this you might have to pull the dishwasher out. While the cycle is running check for 120 VAC g ... Bosch SHU9955UC Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!

... Electrolux Dishwashers

Hi! My bosch SHE43 built in dishwasher is about 2.5 yrs old, dishes aren't getting clean anymore. We have *really* hard water so I use the max rinse agent, but doesn't help. I clean the little canister filter with each wash, and just washed off that grate in the bottom. I also just cleaned the trap under the sink, but it didn't look bad at all. The problem is a grit left on glasses and things just not getting all the way clean. When I remove the grate at the bottom, there's a bit of water

Hello. Let's begin by tossing two cups of vinegar into the empty dishwasher and running it on it's hottest and longest cycle. Always run the hot water in the sink faucet until it is as hot as it gets before starting up the machine. Let that cycle ... Bosch SHE43C02UC Dishwasher

I just bought a used Kenmore standalone dishwasher and ran it for the first time. The dishes on the top did not get clean and the soap did not come out of the closed soup dish. at one point I took a shower and was wondering if that might have influenced the water pressure enough to cause the problem. Is the soap supposed to open during the wash and could the poor water pressure prevent the top shelf from getting properly washed?

The inlet filter is probably clogged. Try letting it fill up. Open the door to stop it right after it starts to wash Pour a gallon or two of hot water in and see it it works better Stop and do this everytime it goes to fill up. If the door opens ... Dishwashers

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.

... Bosch 24 in. SHU43 Built-in Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean

... KitchenAid Dishwashers

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!

... GE GSD5130 Dishwasher

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?

The only thing left is to replace the main control board ... Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr

WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

Dishwasher is 16 months old. Recently, it won't get tea stains from spoons or cups and there is a white film on plastics. I have run unit once with vinegar. I tried using less detergent and no change (Cascade Complete). (Neighbors using same detergnet on different machine with no problems so it's not the water.) I always select High water temp and air dry on normanl wash. My hunch is that the motor is going bad and therefore it is not pushing the water with enough force.

Hello, there are a few thinks to check on the dishwasher. Circulation, drainage - no backflow back into tub, and water temp. If all three are good, then you have hard water. \015\0121. circulation - These MDB models are very good with water circul ... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

I have a Kenmore Ultra Wash dishwasher. Model # 665.15685791. All of a sudden it acts as if it is getting too much water. Water comes over the edge of the interior tub during the rinse cycle, and ends up on the kitchen floor. Is there an adjustment I can make? There doesn't seem to be any blockage, as all the water does drain out of the tub during the regular cylcles. Vince Woodwick [email protected]

Hi, there is a water level sensor and if this is happening then it maybe faulty, and need to be replaced, either this or the controller board that controls it has gone faulty, one needs to troubleshoot to tell.\015\012\015\012\015\012 ... Kenmore Dishwashers

Bought a used Bosch dishwasher. It is all hooked up. I believe water is hooked up bu whe we tuen the washer on it just hums (very, very quietly) it acts as though it isn't getting any water. I have checked the water hose and it is not clogged , what next?

Check that the water valves are opening and allowing water to flow. If the pump is not getting water or is jammed, it will make a humming noise as well ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Gritty dishes My dishes are coming out of the wash gritty. It is as if food has been dried on them. As if the rinse water has particles in it and then they are left on every dish. I have used a dishwasher cleaner several times and I also use the rinse agent in the machine. Nothing is helping. It is getting worse.The inside of the dishwasher. mostly on the top, usually has food residue all over it at the end of every wash. Even the machine is dirty. I'm hand washing everything right now. Any

... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the

Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America

Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.

... Kenmore Dishwashers

Bosch diswasher less than 1 yr old SHE4Apo6UC/05. At start of wash, tub fills with water then cycle goes from ACTIVE to CLEAN within a couple of minutes. Dishes don't get cleaned and water doesn't drain from tub.

I have the same problem. ... Dishwashers

I have a Kirkland Signature dishwasher produced by GE. The dishwasher is leaking from the top of the tub, where the water enters into the top sprayer. Should the top water inlet hose be tight to the top of the wash tub, and if so what can I use to make it tight?

... Dishwashers

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks

It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

We lost electricity very briefly today which caused the dishwasher, washing, drying, clean buttons to blink when the electricity came back on. I opened the door to do a load of dishes hours after the electricity came back on and the basin was filled with water which caused water to spill out of the dishwasher. The basin was empty last night when we used it. It seemed to fill up when it was not running.

It seems unit fill valve is stuck open and water is coming in even when machine is off.fill valve opens up only when u start the unit.2 chks this u can open the door and look at the hole inside from where water comes in.if water is coming in with do ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishes not washed properly. Have tried universal plus at 65deg, the water does not seem to get hot until it is in the main wash cycle. Used to use the universal cycle at 55deg with no problems. Also the dishes are still wet at the end particularly on the top shelf.

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Check the water temperature by using a thermometer inside\015\012the dishwasher to measure the wat ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1374 seconds