Having problems with your Kenmore Dishwashers ?

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

The control panel on my Maytag MDBH970AW is unresponsive, and the latch is stuck in the "open" position (the plastic piece stays pushed in to the handle and won't come down). I've checked that the unit is getting power from the house. Last time I had this exact problem (when it was under warranty), they had to replace the control panel, the latch, and it seemed like most of the door. What should I do?


... Maytag 24 in. MDBH970AWS Built-in Dishwasher

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.\015\012Contact LG @ 1800 243-0000 they may help you out. ... LG 24 in. LDS 5811 Built-in Dishwasher

My Maytag Dishwasher MDB7601AWB is not working. The Rinse Only and Tuff Scrub Plus lights are the only ones lit and the control pad is unresponsive when pressed. Do I need a new control panel or just a touch pad?


... Maytag Dishwashers

Control panel inoperable - 2nd time this has happened. First time repairman said "it was fried" because the panel is just under the countertop - of course this is how it is designed to be. Now it has happened again. My dishwasher is GE PRofile and is now 4 yrs. old. I have tried shutting off power and the controls still do not respond to touch.


Is it operable when the door is close? I'm having a similar problem. The console panel on the top of the door appears to be not working. No lights. No buttons will respond. However when the door is shut, I can squeeze a finger to the start button and ... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Vulcan vsa regency 500e touch control. I have light in dishwasher but when you close the door the main control panel touch pad will not function. Can't operate machine


... Dishwashers

I have unresponsive touch pad, blinks, but the dishwasher does not come on. do I need to replace the control board? or the touch pad? it's a new machine and we have only used about 10 times since we had it. This is the second dishwasher we have purchased. Could it be there's a power serge burning out the boards? Should DW be on a GCFI outlet?


If it's new(less than a year old) it should be under manufacturers warranty. if not under warranty b4 replacing any parts try killing the breaker for a minute or two ... GE 24 in. GLD5860LSS Stainless Still Built-in Dishwasher

Whirlpool DU940 dishwasher. Opened the door and felt that the coil was warm but washer has not been turned on and control panel does not function. Removed power from washer and coil stopped heating but control panel still not working.


... Whirlpool GU2400XTP Built-in Dishwasher

The control panel seems to have filled with water and it is smoking and smells like something is burning inside of the control panel. It is also warm to the touch. What happened?


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

I have a Type S9J1S - SE64A630GB dishwasher which is not progressing beyond draining. With power on it seems to be constantly draining. There are no lights displayed on the control panel strip, and I cannot force it to re-set. This suggests to me that it is an electrical control-panel problem. Any assistance gratefully received!


... Siemens 24 in. SE64A630GB Built-In Dishwasher

No power to kenmore dishwasher control panel no lights on and flipped breaker still does not seem to get power


... Kenmore 24 in. 16032 Built-in Dishwasher

We have a Quiet series 200 Maytag Legacy Series about 2 years old. Some of the buttons on the push pad button panel won't work including the start button. Some will work and some some the lights are green so I know there is power. It seems maybe some of the buttons are broken down so as not to engage. Can the front button panel be replaced assuming that is the problem? Thanks, [email protected]


Hi\015\012\015\012You are right.... if there is power to the unit so the power\015\012board seems to be working fine and the control panel should be replaced. Hope\015\012this helps...please post back for further assistance.\015\012 ... Maytag Dishwashers

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

No kinks in the line. Vent at sink is clear. Will pump some water just not all of it. Pulled left side panel off and removed hoses-no blockage. Pulled drain hose off and turned plump on, seemed to have good pressure/volume. Is this a timer issue? or control panel? Model SHU4022UC/U06


Alright, so you have a Slow Filling Dishwasher. In order to keep small particles of dirt and minerals out of the pumps and nozzles of dishwashers, manufacturers install a small screen in the primary inlet water line to trap any contaminants. Over ti ... Dishwashers

The unit is a Maytag model MDB5601AWW which it has recently began to lose power at the touch pad. The electrical breaker has been checked to confirm normal voltage. Additional investigation suggests that the unit can be reset by (1) disconnecting the power at the breaker, (2) disconnecting and reconnecting the ribbon cable that interfaces the touchpad with the control board. However, the problem reoccurs after a few normal wash cycles.


It sounds to me then that the display board or touchpad needs replacing,you havn't said that it's not doing it's cycles.so it's not causing any washing or cycle problems.i would replace the display board. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1415 seconds