Having problems with your Kenmore Dishwashers ?

Kenmore Dishwasher model 665-13743k601 The clean light is flashing and will not reset. The dishwasher will not run.


Answers :

Hi
If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset.
If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

Kenmore Dishwasher model 665-13743k601 The clean light is flashing and will not reset. The dishwasher will not run.


Hi If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. ... Kenmore Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


Only reset you can do is unplugging power cord for 10 minutes.The control panel it is probably faulty and in need for replacement. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing which says check heat circuit. I've reset board a couple times and run diagnostic. Element tests okay. Light keeps going back to flashing when running dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher

I HAVE A KITCHEN AID DISHWASHER MODEL KUDP02FRSS THAT THE CLEAN LIGHT IS FLASHING 7 TIMES AND IT WILL NOT RUN. HOW CAN I FIX THIS PROBLEM?


... Dishwashers

Dear sirs, I own a Kenmore dishwasher Model # 665.17039400. The clean light flashes 7 times and then repeats. It will not run, only the drain button will work. I changed the heating element from advise on another forum. This did not resolve the issue. Please advise promptly as my wife is going crazy without this appliance. Regards, R. Carmikel


... Kenmore Dishwashers

I have a Frigidaire Professional series less than five years old. It won't run and flashes the wash, clean, and sanitize lights simultaniously. Any thoughts on what the problem is and whether it is worth fixing? This is the second Frigidaire I have had in ten years. The model number is PLD2851RDC3. Any help would be greatly appreciated before I go out and get my third dishwasher in ten years!


Hi.The two lights are not an error code, but they are telling that the machine is in failure mode.The error code is retrieved performing a water/service test.The water/service test is a special function initiated ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

My Kitchenaid dishwasher model KUDS01FLSS6 stopped working. It won't run and the clean light is flashing at me.


You need to clean your dishwasher, leftover soap, food particles, usually cause sensors to be dirty hence it thinks there's some problem with your machine. ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Kenmore dishwasher model 665.17514202 -- "clean" light is flashing and cannot clear it. Unit will not run.


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Kenmore dishwasher, model 665.170 344 01. "Clean" light keeps flashing and will not stop. Have tried everything in the manual and the light still will not stop flashing.


If the clean light flashes 7 times, pauses then repeats...If the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non responsive ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a frididaire proffesional series aquasurge with speed clean dishwasher # PLD4375RFC3 dishwasher there is an Er code that just keeps flashing the china/crystal light is flashing as well as the low rinse light. it used to sound like it was running when you would close the door but nothing was happening inside. any ideas?


... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have a model 665.16032 dishwasher clean light is flashing


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2707 seconds